I just bought a new
Test the batteries somewhere else, the batteries might be bad.
Then test a different set of batteries in the RC.
Volitation helicopter just spins to the left on
If one blade is spinning faster than another, then the helicopter won't lift off. The first thing to check is the gears driving the blade shafts. It could be that one of the gears is not set properly, or there is something caught near the shaft. Pet hair can often wrap around the shaft and cause drag. If the gears appear to be in the correct positions, and meshing with the pinions (small gears) on the motors, and there is nothing wrapped around the shaft, such as hair, I would slowly increase power and see if both motors start spinning at the same time. If they don't, there could be a problem with the motor, or the controller board. If this is the case, it may be repairable, but might be just as cheap to replace the whole helicopter.Hope this helps!
8/29/2013 11:56:16 PM •
xheli 9053...
•
392 views • 0 helpful votes
The main blades on my Madhawk 300 will not spin.
If you hear the motor spinning but not the blades, check the main gear. One crash can knock out enough teeth to cause this problem. You have to remove the landing gear and battery tray to get to it. If the motor isn't spinning, check the motor by applying voltage to it. If that works, swap out the receiver. I've gone through all of the above over the course of time.
9053 will not take off
Lift is a function of the aerofoil. See that heptr blades are not bent or you or someone else have not tried to straighten the blades. They are at a specific angle to provide the required lift.
4/24/2012 5:18:57 PM •
xheli 9053...
•
367 views • 0 helpful votes
My helicopter 9053 will not connect to my controller
The receiver is not binding to the transmitter. Make sure the batteries are in good shape in transmitter. I'm assuming it's a 2.4GHz radio frequency. When you are about to fly, turn transmitter on first after 4-5 seconds turn heli on or plug battery in on heli. In the manual there should be a page describing radio binding. It will describe on what gimbles to move and in certain sequences to complete the process. When the light on transmitter stops flashing means the binding process is complete. Hope this helps.
12/15/2011 8:58:52 AM •
xheli 9053...
•
812 views • 0 helpful votes
9053 bottom blades
Have the same problem with my S107 heli. I determined it's in the speed control hooked to the gyro control. This control feature helps keep heli from turning in flight caused from tork. The lower blades are the onesthat speed up slow down to keep heli orientated. I'm replacing the control board.
12/16/2011 6:45:13 PM •
xheli 9053...
•
343 views • 0 helpful votes
How do i replace tail rotor on v-max hypersonic copter
Depending on what you ordered for replacement parts. You can buythe whole tail boom section or just the motor either way you'll need tosolder those hair like wires to the motor or the PC board. The motor justslips out through the top of the plastic case that holds it. The hair likewires route down the hollow tube to the PC board.
How to remove fuselage
Start with all the phillip head screws that are indented in the canopy and the landing gear needs to be removed also. After removal, carefully split apart.
On my rc volitaion remote on the top the gauge
It's in a safety start up mode so there is no accidental start up of the helicopter while holding model in your hands to turn it on or plug battery in. When ready to fly move throttle gimble to full up then back down to stop. Light should then stop blinking and the next time you move throttle gimble up the helicopter rotors should begin to turn.
10/6/2011 12:43:23 AM •
xheli 9053...
•
258 views • 0 helpful votes
Where doI find the slot to recharge my helicopter
with most rc helicopters you have to disconnect the receiver unit from its battery and connect the charging lead to the battery lead the charger should have 2 leads 1 for the transmitter & 1 for the receiver
hope this helps
Do i need to tune
Hi,
There is a control switch that you have to adjust on the main board. It controls the motor on the rear rotor, the other one controls the main rotor.
Turning and adjusting it is the only one that tunes the entire system.
Hope that helps you out!
Brand new out of the
- If this is a brand new item out of the box, if this were my item, I would send it back for an exchange. The charger never turns green because the battery never gets a full charge. Because of that you won't get a 7.4volt reading out of the battery, Either the battery is not taking the charge or the charger is malfunctioning and not charging proper. The lights may work for a bit while the motor won't spin because a light takes far less voltage than turning a motor. Because you don't know if it is the battery or charger and it is new I have to suggest to take it back. The sooner the better. Messing with it will just void the warranty.
Regards,
Tony
5/22/2011 6:09:26 PM •
xheli 9053...
•
629 views • 1 helpful votes
Not finding what you are looking for?