Wolf Range Cooktops - Popular Questions, Answers, Tips & Manuals

Fuse won't let it shut off? That doesn't make sense. A fuse is made to connect something not disconnect something. I don't know how much you paid that repair man but I would probably call another to verify the diagnosis. Good luck. Semper Fi, Z

Hi,Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...Gas Range Repair Burners Keep on Clicking heatman101

Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...Gas Range Repair Burners Keep on Clicking

heatman101

Interesting, I'm looking for a solution to a similar issue. Our new (7 month old) 30'' Wolf Range has this issue. When both front burners are light, the back burner's electronic starter begins to click, but only when you put a pan on the front left burner. I believe the iron/steel in the pan is causing a magnetic field thats starting the rear burner to go off.. just don't know.. will report back after the repair person comes.

Did the plumber make sure there was not something plugging the gas service connection on the range before he hooked up the gas pipe from the house to it?

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...Gas Range Repair Burners Keep on Clicking

heatman101

Hi,
Here is a tip that I wrote that will help you with that...

http://www.fixya.com/support/r4033033-gas_range_repair_burners_keep_clicking

heatman101

The good news is you have a great product! You just need technique and the "Green" cleaner DeBruce Polish. Use DeBruce Polish and a cloth for clean ups. DeBruce Polish is Odorless, Non-Toxic and non abrasive and perfect on stainless steel, glass cook tops, polished granite marble and more. We buy Debruce Polish at debrucepolish.com

• Firstly clean with DeBruce Polish to clarify area.
• you may have to "re-grain" those finely scratched areas.
• Blend or "scratch out" the misdirection scratch's with new "controlled" scratching, useing a 3M scotch brite #7447 you get at auto parts store (Nappa). Use medium very firm pressure.
  
• -Re-clean with DeBruce Polish. Touch ups are now a breeze.

Use Ceramic Bright from Home Depot.

Remove the oven door skin.

hi friend,
There are a few things to check for. Make sure the electrode ( the small metal piece that the spark comes off from ) is clean and the holes in the burner are clean, use a pin or paper clip to clean out the burner holes and NOT a tooth pick as these can break off and make things worse. Example of a burner. The next thing to check for are the ignition switches under the surface control knobs, the switches can twist and break and keep the spark module on and the spark keeps "clicking" even when the burner is light. If every thing looks good, you may have a bad spark module, replace it. Sometimes cleaning can get moisture into the surface switches, try drying them with an hair dryer to see of this will help.
it sounds like it is the spark module that's making the clicking noise. normally there are 4-6 wires that connect to it , and if you are not comfortable making the repair yourself then I would call an appliance repair company.The part should cost 30-50 $ Good luck
hope this helps u
please rate me.......................
thank u for using fixya
regards
sivaranjini

NAT GAS 4INS WC ..... LPG 11INS WC

try using non scratching comet or ajax and a small amount of water with a scrub brush.

clean the bottom of the knob by using vaccium,remove the knob then clean it.return the knob in possition how u remove.

tnx gerbee

when you turn the knob or push a switch is going to the on posicion so that means that the switch is stuck in one of the knobs , you just have to see witch one is stuck

Youcan try tightening them up yourself. Need two adjustable wrenches, one to hold the connector to the burner and the other to tighten the compression fitting. After that have a solution of water and soap and spray all around your fittings to see if its still leaking, you will see bubbles, If its still leaking you will have to turn yourgas supply valve off and disconnect flex gas lines replace with new ones. After replacing do the same thing spray with the solution to see if they leak.If you dontfeel comfortable doing this dont.

yes it is more effective

Hi,

GE has come up with new products which have high quality insulation. I am leaving it on you to decide which one would fit your pocket by selecting the model from GE's authorised web site.

http://products.geappliances.com/ApplProducts/Dispatcher?REQUEST=COMMERCIALCATEGORIES&CATEGORY=CA0018&SITEID=GEA

Thanks for contacting Fixya.

Use DeBruce Polish I guarantee great results, also perfect on stainless steel go to debrucepolish.com