Whirlpool Refrigerators - Recent Questions, Troubleshooting & Support


Manually defrost the freezer to fridge port with hair dryer on low temp. The fan in side fridge is probably not turn and blowing the cold over

Whirlpool... | Answered 3 days ago


WHIRLPOOL WRF40 Solution to this problem!!! very easy ----I assume you have a problem with the control board switching on and of erratic when you pass setting 3 on the LED display, the designers of this fridge left the calculator at home that day, ask a technician to replace the Resistors 5, 6 & 7 (330 OHM 1/4 watt) on your electronic control board with 680 OHM 1/4 watt. This would solve the problems with this board, the LEDs will not be as bright as they were but still highly visible. Questions? deon@electro-web.co.za

Whirlpool... | Answered on Jan 19, 2019


Some have set screws on back side of handle. Others handle comes off 1st by pulling up hard and fast. Then posts that handle fasten to can be tightened

Whirlpool... | Answered on Jan 18, 2019


There should be one on machine somewhere. Maybe in console area or inside bottom kick plate or inside cabinet.

Whirlpool... | Answered on Jan 18, 2019


Take 2 wires you removed from old switch and place on new switch. With only 2 wires, it doesn’t matter which one goes to either terminal.

Whirlpool... | Answered on Jan 16, 2019


Check the temperature is correct for your setting.

Whirlpool... | Answered on Jan 15, 2019


check for a stuck door switch.

Whirlpool... | Answered on Jan 05, 2019


1) If they have well water, the valve could be blocked with mineral, 2) Regardless of the water source, the actuator coil that opens the water valve could be burned out. 3) There could be ice buildup blocking the water outlet where it feeds into the tray. This can happen if the fridge is not leveled properly and is tilted too far back. It should be tilted back a small amount so that the doors will self close but this same gravity can be your enemy if it lets water linger too long at the fill spout and build up over time. This would be the easiest thing to check first. I would put a carpenter's level on top of the fridge from front to back. If the bubble is slightly forward towards the front, this is probably NOT your problem. If the bubble is smashed up against the front end of the tube and if you can't directly see the filler tube in the freezer, you could try defrosting the freezer with the door open and the fridge shut off for an hour or so. Then turn everything back on and try the ice maker again. In any case, if the fridge is tilted too far back, it would be a good idea to level it anyway. Remember, just enough to let the door drift shut from 1/2 way open. Good luck.

Whirlpool... | Answered on Jan 03, 2019


You’ll have to figure out how that receptacle comes out. Some just snap in. There should be 2, maybe 3 wires going to it.

Whirlpool... | Answered on Jan 02, 2019


Jetblue Airlines Phone Number is a toll-free helpline where on our customers can reach for help from any corner of the globes. issues like luggage lost, discount coupons and means l related inquiry are quite frequent. just reach for jetblue airlines phone number, anytime you require.For more information:- https://airlinesphonenumbers.org/jetblue-airlines/

Whirlpool... | Answered on Dec 31, 2018

Not finding what you are looking for?
Whirlpool Logo

13,572 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Sal De

Level 3 Expert

2699 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Whirlpool Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...