Whirlpool Home - Page 7 - Recent Questions, Troubleshooting & Support

Sounds like your air switch is bad in the little box on top of the motor.It is part # TBS-339RodUS Parts Center888-521-6183

Your motor is shot. you need a new pump. If it comes on and you can hear a hum then it is bad. If you can get us a model number of the pump we can recommend a replacement model for you.

US Parts Center

• Check the circuit breaker to make sure the power is on at the controls.
• Check power coming out of the control going to the air blower

If there is no power coming out of the control when it should be then you have a bad control box.

Rod Kidman

US Parts Center

We locate the "seemingly" impossible...

Ph: 888-521-6183

Fax: 801-417-8027

"Chat Live"

Jet Trim in your jetted bath tub have to be matched up by sight.

Click on the link below to find the brand name of your bathtub, then click on the name.

http://uspartscenter.com/bath-search.aspx

Match up each item in your tub to what is shown online.

If you are unable to match the pieces up to what is shown online to what you have in your tub you may email us photos and we will match them up for you.

send photos to: [email protected]

Rod Kidman

US Parts Center

We locate the "seemingly" impossible...

Ph: 888-521-6183

Fax: 801-417-8027

Jet Trim in your jetted bath tub have to be matched up by sight.

Click on the link below to find the brand name of your bathtub, then click on the name.

http://uspartscenter.com/bath-search.aspx

Match up each item in your tub to what is shown online.

If you are unable to match the pieces up to what is shown online to what you have in your tub you may email us photos and we will match them up for you.

send photos to: [email protected]

You can look under the tub where the fitting is located and there is usually a nut holding that button in place.RodU S Parts Center888-521-6183

The air button on your tub may be bad and not sending enough air to the air switch located on the bath pump.The way to check this is to remove the bath pump and see if you can turn the bath pump on by taking a large straw and blowing into the air switch on the bath pump to see if you can get the bath pump to turn on.If the bath pump comes on then you know you have a bad air button.If you cannot get the bath pump to turn on then remove the air switch and plug the two wires going to the air switch together and then plugging the pump into a power outlet you know has power.If the bath pump comes on then you know you need a new air switch in the motor.If the motor does not come on then you need a new bath pump.RodUS Parts Center888-521-6183

Check the circuit breaker and make sure you have power to the pump.If you have power to the pump and it is not operational when the tub is full of water and you are in it then I would say you have a serious problem.Most all of the older control that Aquaglass has used in the past have been discontinued.You may want to visit this link and identify your control before you begin t trouble shoot your system.RodUS Parts Center888-521-6183

Jet bodies match only the jet trim that goes with them. These are a set and are not interchangeable with other models or brands of jet. Each Bath Part in unique in subtle ways only.In order to find the correct jet body you need to match up the face of the jet trim to what is shown online. Once you know that brand of jet trim we can find you the correct jet body.I would invite you to search our site at US Parts Center and see if you can find the jet face that you have.Once you do we will be able to match up the correct jet body for you.RodUS Parts Center888-521-6183

That control and the pump are no longer made. That system is very old.What brand of pump do you have? If you can get me that information I will be able to find a solution for you.Rodwww.uspartscenter.com