Question edited for clarity.
The whole idea of Self Clean feature is to keep the makers into steady sales of spare parts. The components can only tolerate those temperatures for a number of cycles before elements, door locks and control boards start failing. Consumers don't realize the heat involved!
between 800°F and 900°F
Self-cleaning ovens bring the heat so you don't have to spend hours scrubbing. Traditional self-cleaning cycles heat the oven between 800°F and 900°F, helping turn soil and spills to a powdery ash you can then wipe away. They utilize only heat-no chemicals-and are built to withstand high temperatures. (except they aren't)
Either the door lock has failed or the control board has failed.
https://www.justanswer.com/appliance/6r72n-own-viking-dual-fuel-vdsc530-range-oven-will-not.html
It sounds like the pilot light has gone out. The thermocouple might have failed. It is a gas appliance so you will need a gas certified technician.
Google
Viking (model) manual
..
Check the door gasket for torn or broken attachment tabs. Gently go all the way around the door gasket, wiggling it to see if any part of it pulls out of place. If you find a build-up of dirt, mold, etc,. clean that off. If there is mold present, clean it with a borax solution. Also check the door frame on the refrigerator shell where the gasket is supposed to seal. If you see one area that is particularly dirty or signs of frequent condensation, double check the corresponding part of the gasket for defects.
I'm hypothesizing that a broken section of the gasket sometimes rolls or moves sideways, thus preventing proper sealing.
I have also had problems with the door staying closed if something in the freezer or refrigerator sticks out just enough to put outward pressure on the door (or a similar protrusion of items in the door racks). In that case, re-arrangement of the freezer contents should fix it.
Viking discontinued manufacturing and support for this unit quite a while ago. Most people just replace them as parts are no where to be found.
Geeeer!
Safety First: Before you begin, unplug the refrigerator from the electrical outlet to ensure your safety.
Locate the Ice Maker: The ice maker is typically located in the freezer compartment of your refrigerator. It's usually mounted to the side or top of the freezer.
Access the Ice Maker:
In some refrigerator models, you may need to remove the freezer's interior shelves or baskets to access the ice maker.
Others may have a cover or panel that needs to be removed to access the ice maker assembly.
Identify the Signal Arm: The signal arm is a slender, plastic or metal arm that is connected to the ice maker assembly. It extends over the ice bin or tray.
Remove the Old Signal Arm:
If the signal arm is attached with a screw, use a screwdriver to remove it.
If the signal arm is connected with a clip or latch, gently detach it by carefully pulling it off the pivot point. Some signal arms may have a small locking tab that needs to be released first.
Are you sure it's a good idea to do everything yourself? I don't think you should do that because you can easily connect the wires the wrong way, and I don't even want to think what can happen in that case.
It sounds like there may be an issue with the fan or the control board in your Viking refrigerator. The constant running of the fan, even when the compressor is not running, is not normal. The fact that different repair technicians have given different diagnosis and the issue persist even after replacing the compressor fan motor, suggest that it may be a problem with the control board, which manages the refrigeration system, including the fan. It could also be a problem with the thermostat, or the system's settings. Since the fridge and freezer seem to be at normal temperatures, it may not be a problem with the cooling system. It's best to contact Viking customer service for further assistance and see if they can provide any additional information or troubleshooting steps. If the issue persist, it's best to ask for a senior technician or supervisor to take a look at it and provide a resolution.
If your machine is trying to pump out water that is not there, check the float level sensor. That is the detector that checks for water level during filling. If the pipe/mechanism is blocked, in the full position, the sensor will indicate that there is still water to be pumped out ... that is assuming the water has been pumped out otherwise look for a blockage in the outlet pipe.
Remove and Replace Handles
Using a 3/32"or 1/8" hex wrench, loosen the two set screws located on the side of each handle. 2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching the handles.
There are several options for obtaining a replacement oven bake element for your 11-inch by 16-inch Eaton Viking 305 Wine model with 9-inch contacts. Here are some of the options you can try:
Check if the manufacturer Eaton Viking offers a replacement element compatible with your oven model. You can check their website or contact their customer service for help.
Look online for spare parts stores for appliances. You can search online or local stores that sell oven bakeware for your oven model. Some popular online stores include Amazon, eBay, or appliance parts sites.
Contact an oven technician or servicer for assistance. A qualified technician may be able to help you find the correct replacement oven bake element for your Eaton Viking 305 Wine model.
Look for online forums or groups for appliance owners. There are online groups where homeowners discuss their experiences repairing and maintaining their appliances. You can join these groups and ask questions for help and advice on finding a replacement oven bake element for your Eaton Viking 305 Wine model.
It is important to note that you may need to provide the exact model number of your Eaton Viking oven when searching for a replacement part to ensure you get the correct part for your appliance.
Hi,
I wouldn't pay upfront because the repairman doesn't know what the main problem is. You can first reach out to the product's manufacturer for recommended repair vendors. But if this fails, then you can call your nearest Lowe's or Home Depot for parts and repair assistance.
Thank you.
Hi,
Please power cycle your over from your fusebox if possible. If this is not possible, then please take not of any pattern with the blinking of the oven lights. You can check if the oven door is cracked open or there is excess dirt within the oven. Before setting an appointment to check your gas connection, I would recommend searching for mention of the blinking pattern within the troubleshooting section of the oven's manual.
Thank you.
