USE Popular Questions, Answers, Tips & Manuals

If the shredding disk on your Cuisinart FP-12DC food processor is scraping against the cover and causing damage, it suggests that the disk is not properly seated or there may be an issue with the assembly. Here are some steps you can take to address the problem: Check the assembly: Ensure that the stem adapter and shredding disk are properly aligned and securely attached to the food processor. The stem adapter should fit snugly into the center of the work bowl. Make sure the shredding disk is correctly placed on top of the stem adapter and clicks into place. Inspect the cover: Examine the cover for any obstructions or misalignments that may be preventing the shredding disk from fitting properly. Clean the cover to remove any food particles or debris that may be causing interference. Verify compatibility: Ensure that you are using the correct shredding disk for your specific model of food processor. Different models may have different sizes or types of disks. Refer to the user manual or contact Cuisinart's customer support to confirm that you have the right shredding disk for your FP-12DC model. Adjust the disk height: Some food processors allow you to adjust the height of the slicing or shredding disk. Check if your model has an adjustment mechanism or a reversible disk with different heights. Follow the instructions in the user manual to adjust the disk height to the appropriate position. Contact customer support: If you have followed these steps and the problem persists, it's recommended to reach out to Cuisinart's customer support for further assistance. They will have specific knowledge about your food processor model and can provide guidance or arrange for a repair if necessary. Avoid using the food processor with a misaligned or damaged shredding disk, as it may affect the processor's performance or cause further damage.

Question edited for clarity. We don't do well with abbreviations. See the link https://www.google.com/search?q=gary+fisher+serial+number+year ..

replace the faulty batteries use only the recommended batteries not alkaline batteries

You can use a "Presta adapter", or some floor pumps can do both types of valves. You can get an adapter from any bike shop or even from Walmart: I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

I will preface this by saying that if you don't have the tools, and to a lesser degree the experience, to properly work on your bike it's not worth the time or money to go to indexed shifting on a less expensive bike.. You can probably use the existing rear cluster (freewheel) if it's Shimano. You would also need compatible indexing levers and possibly new cables and housing. Any level of compatible indexing derailleur will work. If your rear cluster is not Shimano, or if it's "Ultra-6" then the freewheel would have to be replaced. In any case 6 speeds in back would be the most I recommend, and also the highest you can go without replacing the chain. If the freewheel is not compatible then you're best off looking for a good indexed used bike and selling yours, due to cost. I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

Since we don't know which camcorder you mean, we have no way of knowing. Look in the manual.

As far as I know "BMX Pro" is not a brand/model. Whatever the brand is, the serial number is often not useful. Contact the manufacturer (name on the head tube where the fork goes through the frame. I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

Owner's manual for bikes will not tell you how to use the gears. Just Google "how to shift gears on a bike" Find one that shows the same type of shifters you have (does not have to be the same brand of bike). Better yet, find a local bike co-op or bike shop to show you on a bike stand before you hit the road (hopefully not literally). I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

in 2050

You can download a manual for almost any equipment by Googling the make and model followed by the word Manual, then follow the appropriate link(s).

You can download a manual for almost any equipment by Googling the make and model followed by the word Manual, then follow the appropriate link(s).

http://www.nodevice.com/driver/company/Philips/PC_Camera.html This should allow you to download driver required. Many thanks Sherrish. Please leave feedback

Post it on ebay, they sell, give away all kinds of manuals. u can try just listing the camera , manual might come up

sir Many models support windows 7, I don't know which model cam you use, if you use an old model, it is recommended to use a video grabber unit with, and you will get the editing software with it.

Try charging it through its USB port. The battery is probaby flat from laying around.

Have you got it fully charged?

http://www.cateye.com/en/support/manual/