Unitech Popular Questions, Answers, Tips & Manuals

The HT630 scanner is a handheld barcode scanner, and an error message can occur for a number of reasons. Here are a few steps you can try to clear the error message on your scanner:

1. Check the user manual: The user manual for the scanner should have a list of error messages and the corresponding solutions. Look for the error message that you are seeing and follow the instructions provided to clear it.
2. Restart the scanner: Sometimes, simply restarting the scanner can clear an error message. To do this, turn off the scanner and then turn it back on again.
3. Check the connections: Make sure that the scanner is properly connected to the host device, such as a computer or a mobile device. Check the cable connections and ensure that they are securely connected.
4. Check the battery: Make sure that the scanner has enough battery power. If the battery is low, the scanner may display an error message. Charge the scanner or replace the battery if necessary.
5. Update the scanner firmware: Make sure that the scanner's firmware is up to date. Outdated firmware can cause errors and malfunctions. Contact the manufacturer for instructions on how to update the firmware.
6. Factory reset: If none of the above steps work, you can try performing a factory reset on the scanner. This will erase all the configurations and settings and will set the device to its original state. Check the user manual or contact the manufacturer for instructions on how to perform a factory reset.

If the error message persists after trying these steps, it's recommended to contact the manufacturer or a professional technician for further assistance. It's worth to mention that, Each scanner has a specific error code, some error codes can only be cleared by the manufacturer, by sending the scanner to repair or by a firmware update.

The HT630 scanner is a handheld barcode scanner, and an error message can occur for a number of reasons. Here are a few steps you can try to clear the error message on your scanner:

1. Check the user manual: The user manual for the scanner should have a list of error messages and the corresponding solutions. Look for the error message that you are seeing and follow the instructions provided to clear it.
2. Restart the scanner: Sometimes, simply restarting the scanner can clear an error message. To do this, turn off the scanner and then turn it back on again.
3. Check the connections: Make sure that the scanner is properly connected to the host device, such as a computer or a mobile device. Check the cable connections and ensure that they are securely connected.
4. Check the battery: Make sure that the scanner has enough battery power. If the battery is low, the scanner may display an error message. Charge the scanner or replace the battery if necessary.
5. Update the scanner firmware: Make sure that the scanner's firmware is up to date. Outdated firmware can cause errors and malfunctions. Contact the manufacturer for instructions on how to update the firmware.
6. Factory reset: If none of the above steps work, you can try performing a factory reset on the scanner. This will erase all the configurations and settings and will set the device to its original state. Check the user manual or contact the manufacturer for instructions on how to perform a factory reset.

If the error message persists after trying these steps, it's recommended to contact the manufacturer or a professional technician for further assistance. It's worth to mention that, Each scanner has a specific error code, some error codes can only be cleared by the manufacturer, by sending the scanner to repair or by a firmware update.

you need a different scanner for that

https://www.youtube.com/watch?v=xwEOWSxe25I

this is for the msr206 as per the descriptive, not the msr406. Following one the answers I shall refer to, it seems likely that the software for 206, 606 and 406 models are interchangeable There's this http://download.smile-files.com/j5GIZFCC+Q0r54J5Xu+QEUuRkxVXhf8/Zfnseyj60WIu+dRjBKOcOU+w0G4a6MVWG+nTF1OSjQVTlqIGXtUyVUqeZBEkmWokMo19GnfNN+AilXbsbzI//zJ3Quc1e1WuKmRA9gZjR/4SOk7wBz5Fxx1DVsgHTk3ZDxl67VxaJNIScybb61Mi5OhbcI6sTDWw0VUl+qV5d/ygamz+r2ZQ4a1qELb9OAiozmlbu55sFILMakSD0QZMiYcCTYqMDuDL2FqwzvcV7MqkF6uKq0XYRugQ8jq37r9ot/CgO/z403y6+cZjvfnNJtSji22L9tUe36mGFcSGzRaB I don't know if will download a lot of extra rubbish onto your computer, or whether it's genuine, or whether it's any good/use. Proceed with caution. I also found this Msr206 software a link to answers to a previous Fixya question My search for msr406 found these results Yahoo Search Web Search some of which look promising ('msr 406 software') Finally, here UNITECH Unitech Global Website Worldwide leading ADC manufacturer is a link to the manufacturer's US website. The NSR206 nor 406 models are found by search (I would think because these are considered obsolete), so I recommend you contact them (using the support link) Good luck ! (be careful with all downloads from unknown websites) 23.January.2015

Unplug the keyboard. Use an air duster to clean dirt/dust/particles out of it. Plug it back in and try it. If that doesn't work, go get a new one. Good Luck

https://www.youtube.com/watch?v=xwEOWSxe25I

You need to check on the website of the company that makes Unitec scanners. They should have the drive available for download is one is available. If you have an older scanner a Windows 7 driver may not be available.

hi, mini123 is not manufactured by Unitech. you can reset the password by the official distributors only. We are one of the distributor for mini123 please check our website for details

yes can do reset but will have to pay for the code

https://www.youtube.com/watch?v=xwEOWSxe25I

MSR206 Software Download for Magnetic Stripe Card Reader Writer

problem can have push buttons or who are stuck trying to reset

Try this driver http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41 and you can use this software http://www.jeppo.dk/download.php?view.1

Not really any difference but note that mrse206 comes in 3 variants ie track 1&2,2&3 and 1,2,&3 while the msr206 can do all 3 tracks. So if you do not want your pos to use track 1 or 3 you can order that version of the Msre206 applicable so your POS cannot read/write to that track .

like me software and driver