Umax Popular Questions, Answers, Tips & Manuals

Only one termination should be powered in a SCSI chain. Generally, it should be the last device. It's been a long time since I've worked with SCSI, but I recall that scanners may be picky about where in a chain of multiple devices they are located; electrical noise on the SCSI data lines causes problems with the scanner electronics. I don't recall whether best results are found from locating it as the first device in line from the computer or the last device.

Do a reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Hi. I have a Mirage II A3 scanner that was working fine till I save it in a closet a few years ago. Now I need it again, but I don´t have the PC I used to have with ISA port... I finally found a brand new PCI card I had in another Umax scanner, so I connected it to the PCI slot in my actual PC. And I cannot connect the scanner... I installed the software correctly, but in Test mode, it gives me a Link failure. Besides, the scanner does its setup when powered on, the lamp goes from right to left, stays there a few seconds and return to its original position. But the UTA and READY lamps keep blinking... I found this page:https://ask.adaptec.com/app/answers/detail/a_id/1869/~/scanner-test-link-failures-with-umax-scanner, that explains this can be fixed upgrading the software, but the link does no longer exist... Could you please send me the software I need to connect it..? It´s really important I can do this. I have a huge job to do but it doesn´t work... I´l be waiting for your answer. THANKS!!

Support That link is to the oem page.

Your OS is not compatible. Period. Either go back to what worked for you or get a new scanner that will work in new environment.

The scan optics are dirty or elements in the scan sensor have gone bad.

Make sure your scanner is connected to your computer with a cable or over the network. Scan your calibration target and save it as an uncompressed TIFF file. Open the Activities overview and start typing Color. Click on the Color to open the panel and select your scanner.

upgrade. run only 1 system

hi there,umax internal tv tuner utv 8300i internal tv tunnar card win 7 drivers. as i understood the support, it is still in beta but should work for your card, too. hope this works for you!you can find the drivers here

http://drivers.softitem.com/list/umax-internal-tv-tunner-card-utv-8300i This should do it.

https://docs.google.com/document/d/1qwnOlYyU7fHDgVA-3qNtIWIPD9dN7ZUCQH030apQpPY/edit download the manual that should help u

get it from the manufacturer web site for that make and model and down load one suitable for win 7

This scanner is Fast SCSI . It was made in 2001. You will need a card in your Mac for a SCSI interface. The cost of the card and scsi cable, if your Mac will accept one, will probably exceed the cost of a newer, high performance scanner. Time to move on? (Umax were not the greatest scanners even when they were made. Umax was a cheaper brand with mediocre software. So how will you get the image into the Mac once you have a connection? Power PC (OS 9) Mac software will not run on OS X.)

I presume this is a scanner that uses a USB connection to your computer. You will find that it does just about nothing until you have it connected both to power and to a computer's USB port. You must also install the appropriate drivers and software. Only then will your computer activate the scanner when you actually try to scan something. The only thing that will activate with only the power cord connected is the scanning lamp inside it so lift the lid and connect the power cord. If the lamp comes on but nothing else, it's just doing what it's supposed to do.

CNET has free drivers or go to website.

please dont.go to www.drivers.com and get a prober driver.install,after the imac "henwise",and reboot.hope it helps.

hi find driver for umax products http://www.official-drivers.com/installer/?seed=umax

Try going into unmax 5600 web site and see if they have a scanner driver load option or a scanner driver CD and copy it. a

Check if the light is on, while the scanned is busy by lifting the lid. If it is dark the lamp or the LED's don't burn and if so, I think you have to start saving for a new one.

The light in the scanner may be burned out so that the document is not being lit during the scanner process. If it is an old scanner I would suggest looking into buying a new one.