Toshiba TEC Popular Questions, Answers, Tips & Manuals

Perform hard reset of electronics and also re install the driver.

document properties, support, check if the label detection is transmission and not none

They are rare. The only manual I know of with tax is this one: https://the-checkout-tech.com/manuals/cashregisters/TEC_MA-1535-2_programming_manual.html Hope it helps

go to test print menu in diag mode set the print conditions set slant line 3 dots align the head on the platen until the printing is clear.

Get someone to replace the main capacitor on the display board

Download driver from seagullscientific and reinstall GBAR As far as I can remember the windows driver used was from seagull scientific. www.bartenderbarcodesoftware.com

Several checks: - Just saying...Ribbon sometimes is placed in the wrong sense and it doesn't print. - Verify the settings at printer driver. Download a powerful Driver from here: http://www.nicelabel.es/downloads/nicelabel-designer-pro/?uid=10004, and test the darkness option by printing with different measures at each time. - If that doesn't work, we can check it again, but you should first test this options.

The printer knows nothing at all about labels, and isn't looking for any gap. I think you specified the wrong settings in whatever software you're printing the labels from - something in "Page layout" or "Format" or possibly "Printer Settings". You need to tell the computer software exactly what labels you're using, or exactly what your label specifications are.

First of all, With any Toshiba label printer, after a parameter reset, you must send a label before doing a feed. Otherwise the printer will try to feed the ribbon. You can use the setting tool to tell set the printer to direct thermal also. Easiest way is to use the windows driver , add a label format coresponding to the one you are using, verify in the support tab that you are in direct thermal, do a test test print from the driver and you'll solve your problem

DEFAULT SPEED IS 9600 bauds, 8 data bits , 1 stop bit no parity. Un fortunateley the best spped avaible is 19200 bds. The pausing is due to too much data transfered trough the serial port. To sole this, increse tehe baudrate and use internal fonts.

As a metter of fact, yes there is a cell detecting the gap. You must turn the Green knob so that the detecting cell is on the notch. You must program the height of the label and in the driver you must give the size of the notch in the Support Tab. D'ont forget to alse specify if it's direct or thermal transfer.

The ribbon error may have different origins:- - check that the winding is externe. - Check that the ribbon core is fitted corectly. - Check that you selected thermal printing in the driver. - Check tha the size of the label is correct and that the interval between label is correctly propgramed. heck that the the value of the ribbon motors is not set to -15.

Check in your software, you may have a alignement option checked or activated.

Label size should be as follows; Width 4.00 cm Height 6.00 cm Margins; L 0.20cm R 0.20cm T 0.15cm B 0.15cm Basically Label setup should be the physical size of the backing paper, the L/R margin size is the gap between the edge of the backing paper and the edge of the label and the T/B margin size if half the gap between two adjacent labels....... Hope this helps.

Hi Ryan, refer to sections 5.2 Overview and 5.3.1 Printing Mode Selection from the following pdf manual. Hope this helps. http://www.cmsitechnologies.com/TEC%20Drivers/BSX45TUM.pdf

First of all check that the ribbon core is correctly placed with the notches fitting on the Green wheels. If th ribbon coe is not secured the wheel will not turn and no ribbon will be detected. If your core is too short and with no notches, you'll have to glue a pice from another core an create a notch.

Here you'll find the right driver together with an ultralite version of Bartender distritubted with every new printer.https://app.sugarsync.com/wf/D1205065_257_623739460

More information needed.

check the dipswitches Sw1-8 -on is for program downloadelse check if the 3 buttons on the front panel are not pressed. - Your firmware is corrupted you have to dowload a new firmware

is this any use How to reset your SX thermal printer back to factory settings