Toshiba Office Equipment & Supplies - Page 5 - Recent Questions, Troubleshooting & Support
How to fix a toshiba BARCODE Printer ribbon take up roller
Hi,
Are you referring to the platen roller? The platen roller is the cylinder that's underneath the printhead which pulls the labels from the roll/box and then pushes it at a certain speed so that the printhead prints onto the label. The platen roller is usually coated in rubber and you can check if the platen roller has some eroded or cut sections.
Unfortunately, the platen roller is a consumable item, you'll need to replace the platen roller. Take a look at our blog for more information about the platen roller.
https://www.bartechsystems.com/barcode-printer-not-working/
When power on toshibs e studio 257 no power in the display , green led iluminating in the display panel
The most common problem is the loss or corruption of the system files. It is necessary to consult the service manual of the equipment in order to enter the service mode and to check the status of the system files and to restore them. It can save you a lot of money that you would have paid to a technical team.https://www.anyservicemanuals.com/downloads/toshiba-e-studio-206l-207l-256-256se-306-306s-306se-306sd-356-356s-356se-356sd-456-456s-456se-456sd-506-506se-207l-257-257s-307-307s-307sd-service-manual/
How to fix paper jam on Toshiba e-studio 203sd
Loading paper that is stuck together, frayed, curled or bent can cause a jam. Overloading the paper tray, loading different thicknesses of paper in the tray or using paper that isn't appropriate for your particular printer can all result in a jammed printer.
How to Fix a Paper Jam in a Printer
- Turn off and unplug the printer. ...
- Remove all printer paper from the tray and then reload it.
- Open the rear access door or duplexer (or any other doors that give you access to the paper's path through the printer)
- Close the doors and plug in the printer.
ADF not working on a Toshiba 3540c
There could be a few reasons why your ADF isn't working properly on your Toshiba 3540c. First, check to make sure that the paper is loaded correctly and that there are no jams. If there are any jams, clear them away and try again.
Another possibility is that the sensors for the ADF might be dirty or misaligned. Try cleaning the sensors and realigning them according to the Toshiba 3540c manual.
If you're still having trouble, it's possible that the ADF itself is defective and will need to be replaced. We recommend contacting Toshiba directly for assistance with this issue.
Toshiba service center philippines
You can locate the toshiba customer service center for the philippines at the link below:
http://www.toshiba.co.jp/tapl/philippines/address.html
4/6/2022 12:52:47 AM •
Toshiba...
•
Answered
on Apr 06, 2022
Toshiba e studio 232 error code E 010 - Toshiba e-STUDIO
hi
Open the transfer cover. Is there any paper on the transport path? YES Remove the paper. NO Is the exit sensor working? (Perform the input check in the test mode: 03-[FAX]ON/[2]/[B]) NO 1) Check if the connector of the exit sensor is disconnected. 2) Check if the connector CN308 on the LGC board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the exit sensor. 6) Replace the LGC board. YES Is the registration roller clutch working? (Perform the output check in the test mode: 03-108/158) NO 1) Check if the connector of the registration roller clutch is disconnected. 2) Check if the connector CN305 on the LGC board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration roller clutch. 6) Replace the LGC board. YES Check the registration roller. Replace it if it is worn out.
Failed to connect to smtp server
hi
Most common reason for 'Outlook cannot connect to SMTP server' error is the wrong configuration settings of Outlook. This happens especially in the case of newly configured email accounts.
A mis-spelled mail server name to a wrong port setting in Outlook can cause connectivity issues to the mail server and end up giving error while trying to send or receive mails.
By default, the port settings for mail related services are these, and a connection problem to these ports can lead to Outlook error:
SMTP - port 25 / 587 POP3 - port 110 IMAP - port 143 Secure SMTP (SSMTP) - port 465 IMAP4 over SSL (IMAPS) - port 993 Secure POP3 (SSL-POP) - port 995
There are also chances that some web masters may have duplicate profiles in Outlook, which will have an old mail server configured in it, and therefore would be trying to connect to the wrong mail server.
Not finding what you are looking for?