The Health & Beauty - Page 3 - Popular Questions, Answers, Tips & Manuals
Where is the breaker switch of my quantum power wheelchair?
However, in most power wheelchairs, including quantum power wheelchairs, the breaker switch is typically located on the main control panel or near the battery pack.
Here are a few steps you can follow to locate the breaker switch in your quantum power wheelchair:
- Start by examining the control panel of your wheelchair. Look for any switches, buttons, or indicators that are labeled as "power," "on/off," or "reset."
- If you don't find any obvious switches on the control panel, check the area near the battery pack. The battery pack is usually located at the back of the wheelchair, underneath the seat. Look for a switch or lever that can be toggled to turn the power on or off.
- In some cases, the breaker switch may be integrated into the power cord or cable connecting the wheelchair to the electrical outlet. Inspect the power cord and check if there is a switch or button along its length.
- If you're unable to locate the breaker switch on your own, consult the user manual or contact the manufacturer of your quantum power wheelchair. They should be able to provide you with specific instructions on finding the breaker switch.
Remember to exercise caution when working with any electrical components and refer to the manufacturer's instructions or seek assistance if needed to ensure your safety and the proper functioning of your power wheelchair.
#58 H-Bridge Defect error code. How to resolve?
hi, H Bridge is the design used for the output of the controller , I'm surprised you getting that message , normally it like 8 flashes etc
so it's a critical error and the controller wherever that is situated either in the joystick or separate unit under the chair , it's worth checking the brushes in the motor just in case they need replacing ,..
Regards
Rob
After changing the batteries on my JI27719 talking scale it does not work
If you have changed the batteries in your JI27719 talking scale and it is still not working, here are a few troubleshooting steps you can try:
1. Ensure the batteries are correctly installed: Double-check that you have inserted the batteries correctly in the scale. Make sure the positive (+) and negative (-) ends of the batteries align with the corresponding markings in the battery compartment.
2. Check the battery contacts: Sometimes, the battery contacts may get dirty or corroded, preventing proper electrical contact. Use a clean cloth or cotton swab to gently clean the battery contacts in the scale and ensure they are free of debris or corrosion.
3. Verify the battery quality: Ensure that the batteries you have inserted are fresh and of good quality. Low-quality or expired batteries may not provide sufficient power for the scale to function properly. Try using a different set of new batteries to see if that resolves the issue.
4. Reset the scale: Some scales have a reset button or a specific procedure to reset the device. Refer to the user manual or manufacturer's instructions to learn how to reset your particular model of the JI27719 scale. Resetting the scale can often resolve minor software glitches or calibration issues.
5. Test the scale on a different surface: Place the scale on a hard, flat, and stable surface. Uneven or soft surfaces can affect the accuracy and functionality of the scale. Try using the scale on different surfaces to rule out any environmental factors that may be interfering with its operation.
6. Contact customer support: If the above steps do not resolve the issue, it is recommended to reach out to the customer support of the manufacturer or the place of purchase for further assistance. They will have specific knowledge about the JI27719 talking scale and can provide you with additional troubleshooting steps or initiate a repair or replacement if necessary.
Remember to provide them with details about the steps you've already taken and any error messages or unusual behavior you've observed from the scale. This will help them better understand the problem and provide appropriate support.
I hope this helps you get your JI27719 talking scale working again.
How do I reboot my ReliOn b/p monitor when I keep getting E1
If you are experiencing an E1 error message on your ReliOn blood pressure monitor, it may indicate a problem with the device or its components. To reset or reboot the monitor, you can try the following steps:
Remove the batteries from the blood pressure monitor.
Wait for 30 seconds to 1 minute.
Reinsert the batteries into the monitor, ensuring that they are properly installed and secured.
Turn on the monitor and attempt to take your blood pressure reading again.
If the E1 error persists, it may indicate a problem with the cuff, tubing, or other components of the blood pressure monitor. In this case, you may need to contact the manufacturer or a qualified technician for further assistance.
It is important to ensure that the monitor is functioning correctly and accurately before relying on its readings. Always follow the manufacturer's instructions and consult with your healthcare provider if you have any concerns about your blood pressure readings or monitor.
Not finding what you are looking for?
