Tag Heuer Watches - Page 5 - Answered Questions & Fixed Issues
Second hand doesn't move for each second
Your TAG is fitted with EOL (end of life) feature. This is the cause of
that 4 seconds interval movement of seconds hand and thus indicating
the time for battery replacement. The timekeeping is not affected by
this- it is just warning to replace battery a.s.a.p.
Find your nearest watchmaker and ask for battery replacement.
Do not forget to rate, please.
Tag Heuer watch losing time
Make sure the voltage on the new battery is correct. Just because a battery is new does not mean it is good. That is likely the problem.
Reset Stopwatch Hands on CL1111 ?
Try setting the crown to position 2 - i.e. the position normally used to adjust the date. Then use the top and bottom stopwatch buttons to adjust the minute hand and 1/10th hand respectively.
5/12/2016 8:37:32 PM •
Tag Heuer...
•
Answered
on May 12, 2016
•
7,393 views
How can I changw the glass for this watch?
In order to replace the crystal on your watch you are going to have to remove the entire movement and use a watch press to remove the crystal. this is not an easy job and should be done by a professionalFirst you will need to get a watch back opener to unscrew the back of your Tag. The three slots should fit into the back of the watch. tighten the opener until it is firmly on. then turn counter close wise until back of case comes off. Next you will need to remove the watch hand and crown. Becareful doing this for pressing to hard will break your set leveler. You will need a thin pin pusher and look on the back of the movement for an arrow pointing toward a hole in the movement. Push down and at the same time pull the stem and crown out of movement. turn the watch right side up and the watch movement should fall out. Place movement on a very safe spot so not to damage movement or dial now you will you be ready to remove crystal Since it is a friction crystal you will need to do use a watch case press . find two die that fit exactly the watch and crystal use a scooped side and place it on the bottom side of the watch press. Next use a flat die to place on top of the case press. place the watch face down. you will be pushing the watch crystal out from the top. Press down on the level and check to see if the crystal came loose, keep doing so till the crystal comes out. finally you will need to measure the thickness and diameter of the crystal and find the exact size. I believe this watch has a sapphire crystal so you will need a sapphire crystal too. Once you buy the proper crystal it is time to put the it in the watch. Place the watch face up in your watch press. and slip the crystal in through the top making sure its perfectly even all around. Slowly push down on the leveler until proper pressure is applied and the crystal snaps in. Now you have new crystal . Clean crystal thoroughly and the inside of the case. Place watch upside down carefully place movement back in. slide spacer in . Now slide watch stem and crown back in push down again on the set leveler with pin pusher. Place case cover on back and tighten properly to prevent water or moisture from entering and you are done. This repair should be done by a professional especially on such a nice watch. Any watchmaker can do this job and will have the tools to do it properly
1/28/2012 7:35:20 AM •
Tag Heuer...
•
Answered
on Jan 28, 2012
•
756 views
Manual for cn1110
HelloGet into this lomk. You can download the manual to your device from herewww.actel.com/documents/CN1110_copper_wirebond.pdf
1/28/2012 2:32:39 AM •
Tag Heuer...
•
Answered
on Jan 28, 2012
•
265 views
I accidentally stepped on my
Has it broken, or just been bent out of shape??? If it is just bent you could possibly take it to a TAG repairer or a watch maker to get it adjusted
1/2/2012 5:16:08 AM •
Tag Heuer...
•
Answered
on Jan 02, 2012
•
321 views
I cant set the time.
sounds like the crown stem may have snapped. Same happened to me and it had to be replaced at a cost of NZD$300. Have you bumped the watch or maybe tighted the stem too tight?
1/2/2012 12:27:12 AM •
Tag Heuer...
•
Answered
on Jan 02, 2012
•
179 views
I cant set the time.
does it have screw down crown if so you need to unscrew it anti clockwise once you do this you can set time etc if it does have screw down crown remember to scew it back its spring loaded so you need a little pressure if you dont it wont be water resistant..
1/2/2012 12:25:27 AM •
Tag Heuer...
•
Answered
on Jan 02, 2012
•
369 views
How to uncrew crown knob WAF1417.BA0823
I have owned two Tag dive watches. They both have issues with the stem. You have to press it in very hard, then turn it counter clock wise tll it pops out, then you can set the time, which needs to be done (at least on these two) on months with different # days. If the stem won't move, place a few drops of "3 in1" oil, or even olive oil on it, give it a few minutes, dry off the outside, then try again - it always works for me. When pushing it back in, turn it clockwise. The next time you set the time, it'll be ++ easier.
12/31/2011 10:47:30 PM •
Tag Heuer...
•
Answered
on Dec 31, 2011
•
293 views
I CAN'T GET THE "SET STEM" TO GO ALL THE WAY BACK
I have owned two Tag dive watches. They both have issues with the stem. You have to press it in very hard, then turn it counter clock wise tll it pops out, then you can set the time, which needs to be done (at least on these two) on months with different # days. If the stem won't move, place a few drops of "3 in1" oil, or even olive oil on it, give it a few minutes, dry off the outside, then try again - it always works for me. When pushing it back in, turn it clockwise. The next time you set the time, it'll be ++ easier.i
12/31/2011 10:46:42 PM •
Tag Heuer...
•
Answered
on Dec 31, 2011
•
453 views
Whats the battery size?
You need sharp nose pliers to unscrew the back and small screw driver to pry out the battery for direct replacement.Maybe 325 but you have to buy fresh ones from Radio Shack not drug stores.
Have a Kirium Formula 1
You should not assume the battery you put in the watch is good. Test it and if it is good (like new) it means you have a problem other than the battery.
I have lost the connecting pin link on my watch
This is most likely a metal band and the part you are talking about is the head piece. I do not know of any outlets that sale the head piece by itself. You will most likely have to buy a replacement band either from the watch manufacturer or an after market watch band supplier like Speidel.
11/7/2011 1:36:05 PM •
Tag Heuer...
•
Answered
on Nov 07, 2011
•
520 views
Tag heuer wk111a-0 instructions
This watch has ETA movement.
The instruction for the watches with the same movement is in
http://www.old-omegas.com/1665en.html
I have installed a new
Hi
Thank you for your question at Fixya,
The solution to your problem is as follows :-
- What you have to do now , is to turn the digital face towards the screen which flashes the digital/date.
- Then you need to pull up the knob out , as you do to set the time, usually.
- Then you need to hold in two auxiliary buttons so that a BAT comes up on the screen , when you see this the flashing stops.
Hope that helps ...:) In case you have any queries, feel free to contact me.
Not finding what you are looking for?