Subaru Air Tools & Compressors - Page 5 - Popular Questions, Answers, Tips & Manuals
Can i use reg.#n246884 on model #2001wk
It is not recommended to use a regulator with a different part number than the original one specified for your tool. The reason is that different regulators may have different pressure settings, flow rates, or other specifications that could affect the performance and safety of your tool.
In your case, the DWB-A16181 regulator is the original regulator specified for the Porter Cable Model 2001WK compressor, and the N246884 regulator is not listed as a compatible replacement in the tool's parts list.
It is recommended to obtain the correct replacement part for your tool, either by contacting the manufacturer or an authorized service center. This will ensure that the replacement part is compatible and meets the required specifications for your tool.
Where can I get parts for a Hyundai Finish Nailer HPT-FIN16-1?
like all things
from them
or used, or new off ebay or amazon
or googling with P/n
first get the manual with part list
the find part there and search online
these steps work for mos things not too not china direct junk
top brand names not nonames (like )
po - ? - p?
Cannot find Thermostat valve in our Atlas copco GA15ff , I check filter housing cannot find where it is fixed
Atlas Copco compressors typically utilize a thermostat valve or a thermostat switch to regulate the temperature and ensure optimal performance. However, the specific design and components may vary depending on the model and configuration of the compressor.
If you are unable to locate the thermostat valve in your Atlas Copco GA15ff compressor but have found two thermostat switches, it's possible that the compressor uses a different mechanism for temperature control.
Here are a few steps you can take to troubleshoot the issue with the dewpoint temperature:
- Check the Thermostat Switches: Since you've found two thermostat switches, ensure that they are functioning correctly. These switches may be responsible for monitoring different temperature parameters within the compressor.
- Inspect for Malfunctions: If the thermostat switches appear to be functioning properly, inspect other components of the compressor for malfunctions or damage that could affect temperature regulation. This includes checking for leaks, clogs, or faulty sensors.
- Consult the Manual: Refer to the user manual or technical documentation for your Atlas Copco GA15ff compressor. The manual should provide detailed information about the components, including the thermostat valve or switches, and troubleshooting steps for temperature-related issues.
- Contact Atlas Copco Support: If you're still unable to resolve the issue, consider reaching out to Atlas Copco's customer support or technical service department for assistance. They can provide guidance and support based on the specific model and configuration of your compressor.
- Consider Professional Service: If the issue persists and you're unable to identify or resolve the problem on your own, it may be necessary to enlist the help of a qualified technician or compressor service provider. They can conduct a thorough inspection and diagnosis of the compressor to identify and address any underlying issues.
Airmate AM78-HCV4 Compressor. How many Amps for model AM78 HC4v please?
Question edited for clarity.
Call 1-888-88EMGLO (1-888-883-6456)
Voltage and Circuit Protection
Refer to the Voltage and Minimum Branch Circuit Requirements
under Specifications.
CAUTION: Certain air compressors can be operated on a
15 amp circuit if the following conditions are met.
• Voltage supply to circuit must comply with the National Electrical
Code.
• Circuit is not used to supply any other electrical needs.
• Extension cords comply with specifications.
• Circuit is equipped with a 15 amp circuit breaker or 15 amp
time delay fuse. NOTE: If compressor is connected to a circuit
protected by fuses, use only time delay fuses. Time delay fuses
should be marked "D" in Canada and "T" in the US.
If any of the above conditions cannot be met, or if operation of the
compressor repeatedly causes interruption of the power, it may be
necessary to operate it from a 20 amp circuit. It is not necessary to
change the cord set.
..
Not finding what you are looking for?