Sterling Plumbing Home - Recent Questions, Troubleshooting & Support

Supplier in the Netherlands, www.novellini.nl

For the 30095PPC are the next parts:


De benodigde artikelnummers zijn:

1 x R02YOB2G-40 (set scharnieren t.b.v. één deur) à € 23,80 incl. btw.


De prijs van de bovenstaande set onderdelen is € 23,80 incl. btw.
Verzendkosten zijn € 7,50 incl. btw.

I have the same issue how do you replace it without removing the entire frame

have a look here it should guide you in the right direction: Sterling Plumbing Service Parts Vista Pivot II Shower Door Height 65 1 2 Max Opening 36

I have the same problem. I'm doing research today, I'll keep you posted. unless you already figured out where to get the seal, please let me know.

where the cold water goes into the hot water heater (marked cold) there should be a "shut off" valve, close it then open it,...sounds like there is something stuck inside "before" all taps,.meaning your taps are fine,...things can get stuck in that one shut-off,....if this does nothing to rectify problem write me back with type of hot water heater,...boiler (tankless) or a tank,...electric or indirect from boiler

Hi I think you need doorsweep which you can find at: CRL lawrence co.They have a wide range of products to fix your problem. I hope that helps.

remove fawcet handle take out the cartride and replace the rubber oring and bevelled or flat rubber washer on end make sure to shut off water supply first if cartridge is in bad shape buy a new replacement one at hardware or plumbing store reinstall

The part # you supplied is for a shower door and has no bearing to your question. There is no relationship. However, I can say there is no adjustment for any two handle shower stem or even single handle stem. Very rarely will just replacing an "O" ring stop a drip unless it it from through the stem itself and comes out under the handle. When in doubt replace the whole stem...shortcuts will only exasperate the problem. There are no shortcuts in plumbing.

Unscrew those screws and the handle will either pull off or unscrew.

Usually the bottom of most framed doors has a chanel which contain door sweep or hollow gasket,all you have to do is pull it and slide the new one in the same place. Please note that some times the end of the chanel is crimped to prevent the gasket to move in and out of the track. I hope this will help.

Sterling like many others made many different types of faucets and stems. To service any of them you need to remove the handle. Then depending on the type of stem you can make your repairs. Most common Sterling stems were brass. Most common cause of slipping is stripped broach on stem and or handle. The broach is the star shaped part of the stem that the handle slides on. If it is stripped replacing the stem and or handle should do the trick. As for the tighteness of the stem, this could be the packing nut on top being to tight or stem may be damaged. Hope this helps. Please share a vote if it does.

curved cut glass will not always be the exact dimensions though they may look identical there should be several set screws on both the door glass frame and the shower glass frame that can be loosened and reset to make the door fit and close and open more properly without seeing the showwer itself i can not tell you exactly where they are but they should be either visible or behind a facade piece of metal frame

You did not tighten the stem enough, allowing the seat to rise just above the cavity where it will sit. You may also have scaling in this area preventing the seat from sitting flush.

Ace Hardware sells that door and you will need to see if they can order the parts but it looka like they sell the doors 36" size so when you order you will need to order for the Sterling Plumbing 1500D-36S "Vista Pivot" Shower Door Fits Openings 31 -1/4" To 36" H 66" . Now if you have not completely finished the shower you could always make the door opening fit what you have.

Try looking at shower door suppliers, and glass companies that make shower doors.

If your water heater is real old, it will slough off the lining and it will clog the hot supply. Try some spray lubricant to see if it will loosen the screw, otherwise you will have to cut off the handle to access the valve. You can replace the stem and the handle. Use a flashlight after you have turned the water off and removed the stem to see if you can find the clog. I use a dental pic to remove the debris when I come across this problem in the field. You can try flushing the system as well but that takes 2 people, one turning the water on and off and the other making sure you don't flood the bathroom. Good luck!

slides out right or left side

http://www.sterlingplumbing.com/contact.strl

The above link is the contact info for Sterling Plumbing Company. You can contact them and they will either be able to mail the parts out to you directly or tell you where you will be able to find repair parts.