Stanley Garden - Page 4 - Answered Questions & Fixed Issues

The lower part of the plastic foot on each tripod leg just screws off. Change just one cell at a time so you don't get confused which way the cell goes in. Use alkaline cells, not zinc-carbon which tend to leak. Good luck!

Cut the end of tube on a angle.There should be a rod with what looks like a plunger at the end.pull the rod back as far as it will go and lock into place.slide tube of caulk into gun with open end of tube towards the plunger.should be a slot at other end where nozzle fits in.take a piece of wire and poke a hole up the nozzle of the tube.release the rod and sqeeze the handle a few times you should see the rod start moving.if not turn the rod until the teeth are facing down.then try again .you should hear a clicking sound and feel pressure and caulk will begin to come out of tube and you will be caulking.Good luck.If you still have problems just come back to fix-ya and we,ll help you through it.

Hello digi..... to set the keypad you need two people. One on a step ladder to push in the button on the garage door opener motor which makes the light blink. then while the light is blinking punch in the 4 digit code and hit enter.

To set the remote, push the button on the motor so that the light blinks then hold the remote nearby and push the button on the remote.

Joe

Thanks for choosing Fixya!

Make sure that you are using staples made for this tool. Remove the staples and look for a jammed staple at the drive head which will block further staple movement. Make sure there is spring tension at the rear of the staple row when the slide is closed. Hope this helps!

To do the job right, you make a miter cut, then a coping cut. There is an excellent article on this at:
http://www.wikihow.com/Cut-a-Coped-Joint-in-Wood-Trim
Getting a nice-looking coped joint is very satisfying, but takes a bit of practice. But it's worth it. Miter joints are great for picture frames and trim on furniture, but not for trimming a room.
Good luck!

yes it has a battery the bottom of the case slides down and, there is a 9 volt battery compartment

The female hos bib connection should have a typical hose washer inside.Often you can't tighten the nut tight enough without this washer, to keep it from leaking both from the hose, and the rest fo the fitting into the washer.

The picture looks a lot like a Solo sprayer I have. I wouldn't be surprised if Solo made them for Stanley. Do a search for Solo sprayers. They have a site. My sprayer is a Solo 425

the darker Seal has come off the plunger at the bottom of the unit , easy 5 min fix , just unscrew the allen keys at the bootonm take off the cover and remove the plunger , you'll see the plunger seal still inside you can fish it out with an allen key or similar tool clip it on again and reassemble

Which model Stihl? If it indeed got so hot the engine seized you will almost certainly need a piston and cylinder. It will not be inexpensive.
Was this saw perhaps operated in a lean condition (metal transfer from the piston to cylinder wall)?
1. Remove the spark plug wire and plug. Remove the muffler, hold a light at the plug hole and inspect the cylinder through the exhaust port. Is it smooth and shiny or does it appear speckled with dull gray spots or smears?
2. Pull the starter slowly, inspect the piston as it rises and falls. Is it a dull gray without scratches and gouges?
3. Hold the light at the exhaust port and look through the spark plug hole, inspect the cylinder above the exhaust port. Is it shiny and smooth or speckled with gray spots or smears?
Any spots or smears on the cylinder or deep scratches and gouges in the piston indicate the saw was operated in a lean condition.
Genuine Stihl parts are proprietary; you must purchase new parts through a Stihl dealer, I do not recommend used parts.
Bailey's offers some OEM Stihl parts. What they offer can be viewed here: http://www.baileysonline.com/category.asp?catID=1666
HTH
Lou

Lowes or Home depot sells replacement sprayers. Hose to tip all included.

http://www.alamia.us/Solo_Sprayer_Parts_s/814.htm?gclid=CNvasPXY1ZsCFdVL5Qod3U4hJw

TreeKisan is a AI- based Platform where tree farmers can know the standing tree market valuation in just 1 minute and sell to potential buyers. Easily assess the economic potential of your trees and make informed decisions. Download TreeKisan Now!

Ensure the membrane is protected with sand before laying the stone to avoid piercing the membrane.

Link : https://heavy-equipmentmanual.com/

Yes, use instructions for bleeding after a filter change. See attached.

If primer lever stroke action seems short, bump the starter so the pump cam rotates away from the pump.

buy better line. and chain link fences are ******* lines

I'm guessing you have fixed this or given up after 13.5 years, but here is my suggestion for the next person who has this trouble. If you ran it out of fuel and left it over the winter, it could have a drop of fuel that hardened and plugged one of the fuel ports in the carburetor. I have had this happen and needed to remove the fuel bowl and poke the dried film with a pin. Put it back together and it started right up.

Do not know what brand that is, but you can find choke cables at lowes, amazon .com. or any number of small engine repair shops depending on where you live. An after market cable could be easier to find and work just as well.

hi, check the wiring diagram harness

John Deere 310g Backhoe Loaders Operation Service Manual