Stanley Garden - Answered Questions & Fixed Issues


On the pivot end of the bladed knife is a black plug that says pull. They actually mean "Push". push it away from the knife body and rotate the handle half it's mounted in, down. The body will rotate in half , revealing the utility blade and more blades in the rear storage.Also note the blade depth adjustment has a locking detent. You have to push it to the right to unlock the utility blade.and push it to the right when retracting to fully retract and lock the utility blade.

Stanley Garden | Answered on Jun 14, 2019 | 2,004 views


Is tranny and various speeds working properly? How about the throttle control? Do you have it set for higher speed?

Stanley Garden | Answered on Aug 25, 2017 | 75 views


Try tilting the machine backwards for a few hours. It may be oil on the piston that is causing a vaccum

Stanley Garden | Answered on May 05, 2017 | 30 views


Make sure it has the right amount of oil in the crank case, if over filled the oil will foam and flow out any place it can, Worn piston rings can cause blowby into the crank case , causing oil to escape from the dipstick tube.

Stanley Lawn... | Answered on Feb 08, 2017 | 455 views


The valve-o-rings + [ parbaks seals ] where the pressure can be adjusted with.
Control the water inlet filter or hose that there are no waterlock couplers are used or is mounted
on the wrong site on the hose , that it is used as water inlet on the tap.

Stanley Garden | Answered on Dec 25, 2016 | 116 views


need-instructions-use-m4f0gcsiyfocfekla1gma2w3-4-0.jpeg

Stanley Garden | Answered on Apr 10, 2017 | 946 views


This is a terrible tool took it apart to get the blade out of the handle and haven't been able to get it back together again.

Stanley Garden | Answered on Jul 24, 2016 | 264 views


Try manufacturer web site.

Stanley Garden | Answered on Jun 12, 2016 | 435 views


Hi Chris:
Seems a bit extreme to consider using the 12 gauge. I've found that a .22 works quite well. (Humour)
Hint! Pressurized tanks must have the pressure relieved BEFORE the lid can be removed.
If the lid has been over tightened or has stuck, you'll need to get more leverage to unscrew it. Sometimes a rag wrapped around it is all it takes.
You can also try pouring hot water over the cap. Lay the tank flat so the rim of the cap gets the heat. Wrap an old towel around it first so it gets a good hot soak.
Should come off without the artillery.
Cheers

Stanley... | Answered on Mar 04, 2017 | 1,250 views


Hi Chris:
It is usually easiest to rest the weight on the tailgate of a pickup truck (or some other device) and then slip out of the harness.
Another technique is to lift bend forward while at the same time rising one shoulder and lowering the other. That will create "slack" on the low shoulder side allowing you to get that arm out.
Cheers

Stanley Garden | Answered on Mar 19, 2016 | 757 views


Gerard, PLEASE contact me at (941) 391-5152 or WFBanach@aol.com so I can hire you to replace the batteries in my Stanley barflex bf0109 light like you did above with vastly more run time mAh. I need someone to do it for me. I'm disabled. I just joined fixya.

Thanks,
Wallace Franklin Banach...

Stanley Garden | Answered on Nov 14, 2015 | 462 views


Maybe from Stanley

Stanley 61804n... | Answered on Aug 10, 2015 | 859 views


The numbers on the side of a framing square are used for many things. The small leg allows you to quickly lay out a wall on16" centers. The other rows of numbers help you figure the correct sizes to cut for hip roofs (roofs that have slope on all four sides.)You can get an instruction Manual from Stanley or it may be availabile on the net. Google (framing square instructions)

Stanley... | Answered on Mar 09, 2015 | 1,001 views


Remove the fittings and check the internal screens, probably rusted and or clogged.

Stanley 1800 PSI... | Answered on Feb 27, 2015 | 134 views


Disconnect the wand from the washer if you get water coming out of the discharge, the problem is in your wand or the line is plugged going to the wand.

Stanley Garden | Answered on May 26, 2015 | 329 views

Not finding what you are looking for?
Stanley Logo

Ask a Question

Usually answered in minutes!

Top Stanley Garden Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2010 Answers

mpservices

Level 2 Expert

190 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29145 Answers

Are you a Stanley Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...