Spy Vehicle Parts & Accessories - Answered Questions & Fixed Issues


I am not sure if this site has one, but give it a try.
ManualsLib Makes it easy to find manuals online

Spy Vehicle... | Answered on Apr 29, 2019 | 30 views


Question?

Spy Vehicle... | Answered on Feb 26, 2019 | 63 views


There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few
for now u can try reliable-store.... let me know if u need help
thanks

Brand Remote... | Answered on Feb 16, 2019 | 91 views


Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I also had an issue with the file so the girl replaced it in 30 mins
there is one more but i don't remember its name it was 2 years back bitman something link this
Try it out brother

Spy Vehicle... | Answered on Jan 31, 2019 | 131 views


Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I also had an issue with the file so the girl replaced it in 30 mins
there is one more but i don't remember its name it was 2 years back bitman something link this
Try it out brother

Spy Vehicle... | Answered on Jan 31, 2019 | 53 views


hello
u will find a lot of wiring diagrams, codes etc and circuit diagrams help books and stuff like this at online places.. like reliable-store
for free

the girl in the chat box can help u instantly... im a frequent buyer there since Im a mechanic so take help from there

Brand Remote... | Answered on Jan 24, 2019 | 43 views


you can try out some guide from reliable-store
they also provide live chat feature for instant help and it's very useful
using that I fixed my own excavator 5-6 times without any other help
plus free so whats harm in not getting

Brand Remote... | Answered on Jan 22, 2019 | 416 views


First replaced the batteries, you may find a CR2032 in there easy to replace then try before blaming any other components

Brand Remote... | Answered on Aug 03, 2014 | 182 views


check on the drivers door

Brand Remote... | Answered on May 11, 2014 | 56 views


Disable the alarm no make sure u always lock the doors

Spy Vehicle... | Answered on Sep 14, 2013 | 91 views


Installations of this nature are usually reserved for professionals. However, get out your installation manual. You will also need two single pulse double throw relays and some diodes. First you will need to locate the ground when running.This wire might be labeled " (-) third ignition". The first relay for the starter will be wired like so: starter wire to 86, fused 12 volts to 87, 30 out to vehicle second starter wire, 85 to ground when running. The second relay will be wired 86 to vehicle ignition, 87 to fused 12 volt, 30 out to second ignition, and 85 to ground when running.

Brand Remote... | Answered on Jan 27, 2013 | 276 views


You need to be more specific if you expect assistance with your problem.

Brand Remote... | Answered on Jan 27, 2013 | 35 views


what brand is alarm? hood pin IS required,ground hood pin lead try to remote start

If you need further help, I’m available over the phone at https://www.6ya.com/expert/stephen_fa62cb6d50fe05e8

Brand Remote... | Answered on Jan 19, 2013 | 163 views


Hi,

Well done.....

Sounds to me like you've installed it correctly.

The only thing I could recommend at this point, is to scan your vehicle's PCM for OBDII fault codes - this will immediately identify which ignition circuit/component may have been disturbed during installation.

Cheers,

Brand Remote... | Answered on Jun 13, 2011 | 233 views


You need to adjust the tachometer sensing wire, it usually wraps around a spark plug wire so I can sense when the car starts. On my spy alarm, the wire was grey. Hope this helps.

Brand Remote... | Answered on Oct 15, 2012 | 1,941 views


This is the only site I know of that has a manual for the install
and user instructions for this alarm. This alarm is hard to install
but the manual shows you how to do it with diagrams.

http://userguides.50webs.com/spy_5000m.htm

Brand Remote... | Answered on Feb 07, 2011 | 2,788 views


The Spy 5000m is a great alarm but difficult to install.
You can get installation and user insttructions from this
site.
http://userguides.50webs.com/spy_5000m.htm

Brand Remote... | Answered on Feb 07, 2011 | 1,469 views


In your local shop - a single AAA is all the Spy 5000m remote fob needs.

Brand Remote... | Answered on Apr 24, 2013 | 292 views


When anything is "Negatively Triggered" this means that usually that, that Circuit, has a resistor of say 10K Ohms, to the Positive Voltage rail. To "Signal" that it is to be "Active: the Circuit is "Pulled Low" by a short circuit to negative/ground. This then gives a negative going signal, that's detected, and the Action performed.


Now usually any Inputs or Outputs have these Pull Up Resistors on the circuit board, and the simple grounding of the wire will "Switch" the Input. So to operate this we would install a switch, with one end on the wire, and the other end wired to the Negative/Ground, when the switch is tripped, it puts a short circuit on that Wire, and in turn, it will operate whatever is operated when that particular switch is tripped.

Most Often an Output is "Tied High" or left alone, as usually the "Logic: of that wire, High or Low, +Voltage or -/0 Voltage, is handled by the electronics internally. You can tell this by measuring the Voltage to earth when the unit is powered up, but not connected. High Out/in puts will have a +12 V voltage on it, or 0V on it. Toggling this line the "other " way activates that wire. If NOT used it is usual to "Tie them high" unless told otherwise.

All/Most Inputs and Outputs aren't needed for actual operation, and can be tested by Tying Inputs & Outputs high or Low, to activate or test a function...

A flame out relay, most likely wouldn't be used, unless you were wishing to monitor for Flame etc. (Sometimes used when running nitro)

Also I find a light bulb on the end of a pair of wires invaluable when testing inputs and outputs, using a small Bulb, you can use it to see an Output or to Trip an input and a visual indication is a lot better when testing

It seem that you do have a good understanding of whats going on, hope i haven't confused you too much and have been of some help..

Brand Remote... | Answered on Dec 30, 2010 | 867 views


There could be an issue with the antenna. Is it mounted on the windshield? If so, try moving it to a different location. You didn't mention the year, make, model of your vehicle but, some cars have a filament in the windshield that interferes with RF signals.

Brand Remote... | Answered on Sep 16, 2010 | 284 views

Not finding what you are looking for?
Spy Logo

Ask a Question

Usually answered in minutes!

Top Spy Vehicle Parts & Accessories Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Rob Sinbad
Rob Sinbad

Level 3 Expert

709 Answers

Norman Al-Anbar

Level 3 Expert

630 Answers

Are you a Spy Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...