Sovereign Popular Questions, Answers, Tips & Manuals

try unplugging the unit and depressing the power switch for 10 seconds and then reconnect to power good luck

see if this link helps you out. https://www.google.co.uk/webhp?sourceid=chrome-instant&rlz=1C1CHBD_en-GBGB719GB719&ion=1&espv=2&ie=UTF-8#q=Is+the+Sovereign+Society+really+a+SCAM

I'm sorry that you are having problems with the manual for your Sovereign AC unit. If you have any questions you need answered about your ac check us out at Air Conditioning Boca Raton

Big hex plug 13/16 deep well socket Small hex 5/8 deep well. Biggest problem With 2 cycle small engine equipment is Ethanol in gasoline softens the fuel lines to the point they look melted and collapse. You can buy non ethanol gas but it costs three times as much

according to this website:http://www.searspartsdirect.com/partsdirect/part-model/Royal-sovereign-Parts/Room-air-conditioner-Parts/Model-ARP900E/3229/0904032/50024022/00001?blt=06&prst=&shdMod= the part is no longer available.when I checked on sears website:http://www.searspartsdirect.com/partsdirect/part-number/900E135/0042/403 it shows that there are no authorized substitutions.

I think you probably could. As most manufacturers of portable AC units allow for this. It's what called a semi -permanent installation . The dryer duct idea will work if the shaft part of the dryer duct is the same diameter as the window mount duct and the shaft of the dryer duct is long enough to go thru the wall and leave enough for the AC Exhaust Duct to hook to. Be sure that the flap door of the dryer duct moves freely and will not get stuck in the closed position. That could be a big problem if it does.
Keep in mind, you will not be able to add any length the AC duct hose. It must remain the same.

Hope this helped answer your question and things for choosing FixYa.

Check the wter tank it must be full and needs emptied before the unit will continue to run. If your runnig a drain hose, then the hose may be plugged or the float switch for the bucket is either hung up or malfunctioning.
If this was helpful a vote with the thumbs up would be greatly appreciated for the free advice.
Thanks and if you need more let me know.

Here is the solution to all parts! :)
http://www.searspartsdirect.com/partsdirect/part-model/royal-sovereign-parts/room-air-conditioner-parts/Model-ARP1000ES/3229/0904032/50028633/00001

Hello
You can use bleach to wash away the black mold.
Thanks

remove the screen to get to it but follow these precautions.
In order to get mold out of various surfaces, it is important to first obtain proper protective gear. You should check to make sure you have all the necessary protection before you start, such as goggles and a disposable outfit which you can wear during the cleaning.

The first step is to wet the moldy area with water and soap spray. This stops the mold from continuing to spread through the air, which it will do if you do not spray it first. Then, you can use a vacuum to **** away remaining mold spores from the affected area and any surfaces close by which might also be affected by mold spores.

Next, you want to be sure to rinse all areas where you have scrubbed. You can use a wet-dry vac if necessary if too much water has collected. You should then take some bleach and water and apply it to the surface where containing the black mold. Warning: do not mix bleach and ammonia! This can lead to a deadly combination of gases. Make sure you follow the instructions on your cleaning ingredients labels.

You will probably have to leave the solution on the affected area for 6-8 hours or thereabouts. It should be able to dry on its own. You can also use fans, dehumidifiers, and any other type of air circulation device to let the area dry as quickly as possible.

It is important to note, however, that it is very important to let the mold dry; otherwise, it will reproduce. Every mold spore must have a chance to be completely wiped out to prevent it from coming back at any further date. Once the entire contaminated area has been scrubbed away, it should be okay to start using the previously affected room again for any usual purposes.

Ultimately, black mold removal must be done with care and caution. You must ensure that every surface which has been affected is thoroughly cleaned. If it is not, you run the risk of mold returning which can cause serious health problems, as mold is a deadly substance and can create huge issues for any house or building which is affected by it.

Be sure to properly protect yourself when cleaning non-porous materials or any other household surfaces while you remove mold, both to prevent damage from the mold itself and from the chemicals you use to clean it away. This is very important to ensure good safety and preventative measures for mold removal and permanent care and treatment of the moldy spots.

The drain plug for draining accumulated water is located on the back of the unit's lower left side (as you're facing the back just to the left of the cord keeper. Unplug it, disconnect the exhaust hose and roll it to a drainage area. Unscrew the plug and let it drain. Securely replace the drain plug when draining is complete.

Hope this helped you.

Try draining the unit. If the drain pan is full, the unit won't turn on.

The evaporator is mounted above and on top of the heater unit inside the box. It sounds like this cleaning is the issue if cool air is coming out. Very slow though, right? Good luck and keep me posted please. - Ned

Your not saying what brand or model you have but it sounds like you don't have the right drain system

LOWeS or home depot. or order on line from the manufacture website.

Have you cleaned the evap coil? Most often smells come from the evap coil. A bleach type product used for cleaning will solve this problem. Thanks