What is the meaning of code C4-10
The error code C4-10 on a Sharp MX-2600N printer indicates a problem with the Fusing Unit temperature sensor. This error code typically occurs when the fuser unit is not heating up properly or the temperature sensor is not functioning correctly.
Here are some steps you can take to try and resolve the issue:
- Turn off the printer and unplug it from the power source.
- Wait for a few minutes and then plug the printer back in and turn it on.
- Check the fuser unit to make sure it is properly installed and seated in its place.
- Inspect the temperature sensor and its wiring for any signs of damage or wear. If the sensor or wiring is damaged, it will need to be replaced.
- If there are no visible signs of damage, the temperature sensor may need to be reset or replaced. Consult your printer's user manual or contact a professional printer technician for assistance.
It is worth noting that attempting to repair the printer yourself can be dangerous and may void any existing warranty on the device. It is recommended that you seek the help of a professional printer technician to diagnose and fix the issue.
How to open back cover sharp led backlight tv model 2T-C45AD8X
Hey, The Sharp LED Backlight TV model 2T-C45AD8X's back cover can be opened by performing the following steps:
1) Cut the TV off from the power supply.
2) Place the television flat on a soft surface.
3) Using a screwdriver, find the screws that are attached to the back cover's borders.
4) Carefully remove the back cover to have access to the internal parts.
Thanks!
Sharp Drawer Microwave SMD2489ES. All indications of *****.
It is a motorized drawer and I doubt it likes being opened manually. It would need to be repaired professionally due to the inherent dangers of microwave energy. The drawer motor would be operated by a relay.
Did you read any reviews before you purchased it?
IanFromOhio
a year ago
Thumbs Down
- Looks great but features are bad.
Drawer microwaves and this model in particular look great. We did a big reno in December and this is now in the island. Looks good and functions as a basic microwave. Everything else is just south of mediocre. I'd suggest you get a drawer microwave from another company. Bad Stuff: - door opens/closes very slowly (~4 seconds)... doing a 30 second reheat now takes 4+4+30+4+4 = 50% longer just standing around. Likely similar with other drawers, but an unexpected negative. - doesn't let you tell it to start until fully closed - its default sounds and reminders are ridiculously annoying - beep-beep-beep on finish, and 10 seconds after that, and 10 seconds after that, and.... on and on - it forgets all settings during a power outage, turning back on the annoying sounds - and forgets your network connection - but good news, you won't want to use that feature - controls are not intuitive - classic 40 buttons where you use 5 The WiFi & App - hilariously bad. Design in your head the things you would want in a microwave app. Sharp engineers designed the opposite. Can you set the alarm settings in the app? No. Do you get a notification each time the microwave finishes cooking? Yes. I guarantee you will delete the app within 48 hours. Hand Wave to open. Neat right? No. Take how long it takes for this thing to open/close and add another 4-8 seconds of waving your hands (which are full food, else you'd just press the button) to then wait for the drawer to open. Push to close works well, but it reacts in a weird way, so some concern I'm breaking it. I stopped doing wave to open after the first week and stopped trying to demonstrate it to friends after one month (cause it will make you look silly). Height - just tall enough - fits a Venti coffee Cooks at 950 watts - basically the same power as a college-dorm microwave Cost. my god, how much did I spend on this. The good: Looks good Flush install if you have a good installer; mine is shown in a 30" wide lower microwave cabinet by Medallion Reheat sensor cook works well push to close works. It was suggested that I buy a Sharp because they have the patent on the drawer microwave and everyone else is just a re-labelled Sharp. I would suggest you give the others a look. They may be using the same hardware, but hopefully they have a more customer-focused interface and better software engineers working for them.
Reviewed on bestbuy.com
TV Sharp LC-40LE830U. My front panel ys disabled and my remote control don't work. I can power on/off only. How can I enable my front panel without use remote control? or reset factory settings?
If both your front panel and remote control are disabled, the best option would be to perform a factory reset to restore the TV to its original settings.
To reset the Sharp LC-40LE830U to factory settings:
- Unplug the TV from the power outlet and wait for at least 60 seconds.
- Press and hold the power button on the TV for 5 seconds while the TV is still unplugged.
- Plug the TV back in and turn it on using the power button on the TV itself.
- Once the TV is turned on, press and hold the "input" and "volume down" buttons on the TV simultaneously for 5 seconds.
- The TV will then enter the service mode menu.
- Press the "menu" button on the remote control to navigate through the menu and select "option."
- Select "factory reset" from the options menu and follow the on-screen instructions to complete the reset.
Note: The factory reset will erase all custom settings, including parental controls, picture, and audio settings.
I am trying to troubleshoot a sharp aquos tv.
The 1 blink followed by 3 blinks error code on a Sharp Aquos TV usually indicates an issue with the mainboard or the power supply board. It's difficult to say whether replacing the power supply board will fix both the black screen and the blurry/discolored picture issues without further diagnosis.
Here are a few things you can try to troubleshoot the issue:
- Check all cable connections: Make sure all cables and connectors are securely attached and not damaged.
- Perform a hard reset: Unplug the TV from the power outlet and wait for 60 seconds before plugging it back in. This can sometimes reset the TV and resolve any issues.
- Check the mainboard: If the power supply board appears to be functioning properly, the issue may be with the mainboard. Inspect the mainboard for any physical damage or burnt components.
- Test the power supply board: If you have a multimeter, you can test the power supply board to see if it's supplying the correct voltage to the mainboard and other components.
- Contact a professional: If you're not comfortable troubleshooting the issue yourself, it's best to contact a professional repair service or the manufacturer's customer support for further assistance. They may be able to provide additional troubleshooting steps or recommend a service center for repairs.
It's important to note that taking off the back panel of a TV can be dangerous, and if you're not experienced with electronics repair, it's best to leave it to the professionals.
How to disable the FPA for sharp LC-40LE830U?
FPA stands for Front Panel Lock, which disables the buttons on the TV's front panel. To disable it on the Sharp LC-40LE830U, follow these steps:
- Turn on the TV.
- Press and hold the VOL- button on the TV's front panel.
- While holding the VOL- button, press and hold the INPUT button on the remote control.
- Hold both buttons down until the message "Service Menu" appears on the screen.
- Release both buttons.
- Use the arrow keys on the remote to highlight "Option" and press ENTER.
- Highlight "FPA Lock" and press ENTER.
- Change the setting to "Off" and press ENTER.
- Press EXIT to exit the service menu.
The FPA lock should now be disabled, and you should be able to use the buttons on the TV's front panel again.
Not finding what you are looking for?
