Samsung Refrigerators - Popular Questions, Answers, Tips & Manuals

Check the coolant level and pressure when cooling. You may need to evacuate the system and reload it with the correct anount of gas.

Check the Control Settings: Ensure that the temperature settings for both the fridge and freezer compartments are appropriately configured. Sometimes incorrect settings can lead to cooling problems. Make sure the fridge is not in demo mode. If it is, disable demo mode by referring to your user manual. Inspect the Door Seals: Damaged or worn-out door seals can cause cold air to leak out, resulting in insufficient cooling in the fridge compartment. Inspect the door seals for any cracks, tears, or gaps. If you find any issues, consider replacing the door seals. Evaporator Coil and Fan Check: The evaporator coils in the fridge play a crucial role in cooling. If they are frozen or malfunctioning, it can affect cooling. Similarly, check if the fan responsible for distributing cold air inside the fridge is working correctly. Reset the Refrigerator: Sometimes a simple reset can resolve cooling issues. Unplug the fridge from the power source for a few minutes, then plug it back in. Observe if there's any improvement in cooling after the reset. Compressor Overheating: You mentioned that the compressor is very hot. An overheated compressor can impact cooling. Allow the compressor to cool down completely before switching the fridge back on.

Compressors are noisy due to its job. Check there is no packaging between the motor and any other part as that can increase the noise.

could be just the coil on the valve, but most more likely valve getting stuck as it opens. somtimes can take apart and clean, will work for awhile, but if have the cash best just swap it out. will save you hassel down the road.My Aplogies I was under the impression you had already located the valve. I as I have not seen unit I can not give the location, However since it is on the water system, I would trace water tubing from where it connects to unit. It should not be far from inlet connection. Look for tubing going to a valve with wires ontop, ensure after the valve is where you whish water/ice to come out. Once that is located take photo and order new valve, or secure water remove and clean valve. Note have container ready as water will leak once you remove valve.

Unplug the fridge, wait 2 minutes and plug back in. If symptoms remain then likely it was damaged. If you don't have a whole house surge suppressor then you need one. Modern appliances are extremely susceptible to voltage spikes.

First: i don't know. In the manual there should be some pages for solving dysfunction and what the lights mean. Always check for damage on the closed and pressurized system, including inside, where the tubular radiators are, mostly half within the panels. Those may have broken when using tools to remove ice or been hit rough with some object. For a right understanding: the fridge must not be shaken or tilted and carried. When this has happened, then the evaporation fluid or refrigerant can be mixed with the oil that resides on the bottom of the compressor. It may only have a small sponge to clear the fluid from a little oil contamination. What finally solves the mixing is shutting the fridge off for 24 hours and when not completely satisfied with the result, immediately for another 24 hours. Another thought is that a fridge may not function at all, in a cold room. Transfer of heat is totally not the same at all temperatures. Many people have been the same disappointed as you, thinking they can find a cold place for the fridge or freezer. So, when this has happened when the room temperature dropped dramatically, get it out of the cold or shut it down because it performs at its maximum capacity. That is where my bet is at. The radiator at the back can also not function right when it is close the wall and/or an object is placed right above it. The heat must be dispersed. Best of luck

check the defrost control board could be malfunctioning

temp too warm if temp is ok by checking with thermometer then replace temp sensor

Here are the parts suppliers. It does look like that part is not available separately. Fix with epoxy or have one 3D printed. https://www.google.com/search?q=samsung+rs7567bhcsp+parts ..

Question edited for a lot more clarity. Please proof read before Posting.. Question moved from Cellphones category. 40,000 to choose from RD is air damper iced up fault. The damper in the freezer spins around to close/open the air from the freezer to the fridge. It ices up from time to time, or the damper motor, or sensor that reads it's position fails. Apr 27, 2010

Hi. My samsung RL39WBMS fridge/freezer shows rd in the ...

If you can spell it, you can Google it! Lots more in the link. 'make model (what it is)' in all questions please. https://www.google.com/search?q=Samsung+refrigerator+RD+code ..

The versions are the software and firmware adjustments. Always replace like for like, that will avoid issues.

Question edited for clarity and typos. When they regassed it, they didn't check where the leak was. It is still leaking and you have lost gas again. https://www.google.com/search?q=Samsung+RS20+fridge+freezer ..

Question edited for 'make model (what it is)' in that order and first in the question please. Part number is spot on. A bargain at just $200!! https://www.google.com/search?q=DA41-00451 My advice with control boards is to get professional diagnosis due to the cost of them. Always try cleaning the edge connector with electrical switch cleaning fluid. https://www.google.com/search?q=Samsung+RSH1JLMR+parts ..

I would power it off, wait for 5 minutes and plug it back in. If the logic board has frozen, that will reset it.

Depending on how you "defrosted the actual ice maker", i.e., if you used a hair dryer, you might have deformed the plastic. Unfortunately this bin needs to be air tight, which may be why it is misaligned now. You might need to call for Refrigerator Repair Service near you to see what is happening, and if you may have made it worse.

Unplug for 5 minutes to see if it'll reset to foctory setings.

Question edited for clarity and typos. Question moved to maker category. Duplicate questions deleted. Refresh page to see your question. It sounds like the ice level sensor. when that rod is covered in ice, the system shuts off. Google samsung model parts diagram https://www.google.com/search?q=%E2%80%8Bsamsung+model+parts+diagram ..

Your fridge is no longer working and you need to buy a new fridge.