Samsung SyncMaster - Recent Questions, Troubleshooting & Support


Hi,
You can find the same from samsung Website, check in below given site
http://www.samsung.com/in/support/search/supportSearchModelResult.do?menu=SP01&searchWord=SamsungSyncMaster710m17inchLCDMonitor&default_searchInputBox_value=Enter+model+number+or+keywords&searchInputBox=Samsung+SyncMaster+710m+17+inch+LCD+Monitor

Samsung... | Answered on Jul 08, 2019


thanks but The monitor was checked, the technician told me that he tryed to get the video card of the monitor Samsung 216 BW but they don't know were buy a part like this to replace it the broken.
If you can please, let me know where I can buy parts of Samsung monitor 216 BW.

Thanks.

Samsung... | Answered on Jun 21, 2019


You can try lowering the refresh rate to a lower value.
Ex. from 100Hz to 60Hz

Samsung... | Answered on Mar 23, 2019


First of all plug another monitor to the VC on your PC and do the same for the SamSung"I over heat"SyncMaster2 053BW.
Oct 23, 2009 - This is how it went for me..I have a Samsung SYNCMASTER2.gif 2053BW. I leave my monitor on and let it hybernate when I shut down PC. I'm 3 months outside of my warranty. Two weeks ago something started happening. I boot PC and video doesn't come up for 10 minutes, and when it came up it worked perfect. VC/Monitor/MB?? It became 20 minutes and ...now..I have the analog/digital box in top left screen, power light on monitor flashing, no menu available on monitor and none of the other buttons work for anything. I test the monitor on Laptop..nothing(same as above)..I break out the old(working) monitor from deep within the closet. Plug it in and I'm up and running. So...

HOW TO OPEN A SYNCMASTER 2053BW

NO SCREWS!!! Assuming that the stand mount has been pulled out..The seam around the screen frame is where you start. The frame has the prongs, the back cover has what the prongs slip over.The frame is coming off first! I got the side to open by finger, then used a small standard screwdriver to pry ever so gently(lifting frame from rearcover). Leave the power button assembly on the frame, pull wire only a little to relax any tension..you get about 3/4" in extra taped to panel. The hard part is done.;) Still holding the frame...Now lift the panel (where the power button assembly wiring goes under panel) with the power housing that is under it as a whole and you will see where the powerbuttonassemble detaches.Remove frame. Now..holding edges of panel into back cover, lift and flip the whole thing over and place panel face down on a perfectly flat surface..a towel on my desk works. Lift and remove back cover.Your now looking at the back of the board housing. The ribon is simple, on the panel end of the ribon, squeez the outer clips together and slide it away against the panel..The secondary tin plate is removable, two clips super close to where the sets of wires come around the housing and into the panel.Unhook the 4 plugs(pink inside/blue outside)...Now lift the power housing off of the panel. The big board has the power. One screw to remove a ground plate first. Two screws to remove power board. Pics from phone.56ec44b.jpg
aae8fab.jpg
Reassemble but DO NOT re-snap the frame into place....yet... Test it! There is a reason the caps got hot in the first place, therfore it has a good chance of happening again. This is not fullproof...but.....mine has been on now for close to 6 hours with no glitches whatsoever. So I have resnapped mine back together. I hope you can too. - I must also add that this is one of the best producing monitors I have ever seen...in 60hz. The clarity is top notch. If you purchase one get the extended warranty. FYI...I paid $4.00 for those caps.

Samsung... | Answered on Mar 15, 2019


put another monitor on your computer first so you can see to get on the internet . ..then go to the samsung site and download the drivers for your samsung model and install them into your computer. ...after you install the new drivers then put your samsung back on and your computer should read your monitor then and work

Samsung... | Answered on Jan 08, 2019


Hi,
You do not need to install any driver to use this monitor. The operating system has built-in drivers for this monitor

Samsung... | Answered on Jan 08, 2019


hi

I am a technician-informatic. I have repaired about 60 Lcd Samsung monitors with this problem - not optimal resolution mode and dark screen problem. So i decided to made manual how to repair lcd samsung monitors.The repair process is very easy and simple 10-30min. does not need a lot of experience in electronics and expensive instruments.

if you are interested check it.

Samsung monitor repair manual guide 710n,913v,510n more
or just enter number in search field: 220409788372


thank you

Samsung... | Answered on Dec 19, 2018


This problem often occurs in samsung SyncMaster LCD monitors.

The solution is open your look for the LCD monitor power supply module (which have PCB connector to the AC power), on that board look for capacitors, now look for broken one which upper part is bloated, like the image below:
e5e5c21.jpg
If you find a damaged capacitor as in the picture then you should replace it with the same value.

Samsung... | Answered on Dec 18, 2018


replace capacitors 1000mf/25v 470mf/25v...

Samsung... | Answered on Dec 18, 2018


I have to send mine back to Samsung because of the same problem. Samsung is now like Toyota not disclosing know problems.

Samsung... | Answered on Nov 21, 2018


5 year old hyjacker, vinay.
you forgot to say connected to what?
is the screen only dim or dead.? even more important clue.

RTM
read page PDF 17, ?
the OSD screen must work or the monitor is dead

http://downloadcenter.samsung.com/content/UM/201205/20120517112305649/SA10-04Eng.PDF







base pages
https://www.samsung.com/us/support/owners/product/lcd-monitor-a10-series

Samsung... | Answered on Sep 12, 2018


Please try this:
Service manuals:
http://elektrotanya.com/?q=showresult&megnev=samsung&megnev2=940&kategoria=monitor&kat2=schematics

Please leave rating if it helps.

Samsung... | Answered on Mar 14, 2018


from user manual troubleshooting section
(When connecting D-Sub cable) Check the signal cable connection. (When connecting DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press Source button to have the monitor double-check the input signal source.

Source button Activates a highlighted menu item.
/ Push the 'SOURCE', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's port using the DVI cable.
https://images10.newegg.com/User-Manual/User_Manual_24-001-063.pdf ninth page in user manual
source button fourth from the left when facing monitor. looks like a box with an arrow pointing left.

Samsung... | Answered on Mar 06, 2018


Try using a different HDMI cable. If issue persists, try using the DVI port and a DVI cable. If not then try removing your video card and just use the on-board video option of your PC. If issue persists, try a different monitor.

Samsung... | Answered on Feb 20, 2018

Not finding what you are looking for?

-1,842 questions posted

Ask a Question

Usually answered in minutes!

Top Samsung Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

asber

Level 3 Expert

296 Answers

RONALD CARTER JR

Level 3 Expert

438 Answers

Are you a Samsung Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Samsung Computers & Internet

  • Forum

View Most Popular

  • Samsung Computers & Internet
Loading...