Russell Hobbs Logo

Russell Hobbs Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 237 Products
  • 1K Answers
  • 103K Views

CONTACT RUSSEL HOBBS COMPANY

Russell Hobbs... | Answered on Mar 05, 2019


To disassemble the Russell Hobbs 15081 steam glide iron, you have to remove the two hidden screws on the handle. To locate the first screw remove the two adjacent blue buttons which are each held in with two hidden clips front and rear, so lever out with small screwdriver or similar. The second hidden screw is under the pivots of the water inlet lid.(I broke one of the plastic pivots but no big deal). Then using a thin blade, separate the top half of the handle from the bottom half of the handle. A bit of force is needed as there are more plastic clips. I started from the rear.
Once the top half the handle is removed, other screws become visible, so teardown is not hard, just note which screws go where, as they are different lengths.
My problem was that some of the screws/bolts were so corroded I needed to drill them out. The thermostat was also corroded, which probably explained why the thermal fuse had blown. The element was fine.

Russell Hobbs... | Answered on Mar 04, 2019


To disassemble the Russell Hobbs 15081steam glide iron, you have to remove the two hidden screws on the handle. To locate the first screw remove the two adjacent blue buttons which are each held in with two hidden clips front and rear, so lever out with small screwdriver or similar. The second hidden screw is under the pivots of the water inlet lid.(I broke one of the plastic pivots but no big deal). Then using a thin blade, separate the top half of the handle from the bottom half of the handle. A bit of force is needed as there are more plastic clips. I started from the rear.
Once the top half the handle is removed, other screws become visible, so teardown is not hard, just note which screws go where, as they are different lengths.
My problem was that some of the screws/bolts were so corroded I needed to drill them out. The thermostat was also corroded, which probably explained why the thermal fuse had blown. The element was fine.

Russell Hobbs... | Answered on Mar 04, 2019


Wattage may very with the power used for microwave.

Russell Hobbs... | Answered on Mar 04, 2019


The magnetron has a 100% duty cycle on full power and reduces to 20% on low power. That means that it produces full power for 20 seconds and no power for 80 seconds on low power during the cook cycle.

Russell Hobbs... | Answered on Feb 10, 2019


are talking the blade inside the canister if so it unscrews from the clear handle and view area. otherwise if you mean the chuck below when the canister is lifted off that is held on by a fastener right in the middle dead center

Russell Hobbs... | Answered on Feb 08, 2019


If that's what it says in the manual, that's as far as you'll get.

Russell Hobbs... | Answered on Feb 02, 2019


SORRY BUT WE DO NOT SEARCH FOR REPLACEMENT PARTS HERE ON FIXYA

Russell Hobbs... | Answered on Jan 21, 2019


The internal fuse has probably blown or the wire is damaged in the machine. Preferrably don't try to repair it if you don't know a lot about electronics. The chance of shocking yourself is too high if you are not a qualified electrician.
I am sorry, but throw it away. The safety risk is too high to try to repair a device of this price.

Russell Hobbs... | Answered on Jan 15, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Russell Hobbs Experts

ray gallant

Level 3 Expert

60482 Answers

Tom Chichester

Level 3 Expert

50967 Answers

JonSnell Electronic
JonSnell Electronic

Level 3 Expert

29208 Answers

Are you a Russell Hobbs Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...