Royal Sovereign Popular Questions, Answers, Tips & Manuals

The external water tray is to be used for draining the unit when the internal water tray is full. Position the external water tray under the drain at the bottom rear of the unit then remove the cap and plug and let water fill the tray. This was copied from royal sovereign instructions.

Fergusons n other hvac supply stores sell ac parts, etc...not sure if need hvac license to buy freon, depending where you're located, but I kno can buy freon online, but still not sure if going to ask contractor/hvac # once get to purchasing screen....as to where u need to put freon in that particular model, always ask Google n guarantee somebody made a video somewhere that will pop up, giving u a tutorial on it.

Either compressor not working or out of refrigerant. If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Probably needs the Freon gas topped up.

What does the manual say? What model number? Cords or plugs? If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Does the display work or nothing at all? If nothing at all, check your outlet. Also, there may be a fuse or circuitbreaker inside the air conditioner that needs to be reset or replaced. Unplug the unit before attempting to find or replace. If the display works, did you empty the water? Is it upright and level?

That is usually a burned out bearing on the motor of the fan.

trash in blower or bearings going bad.

since an AC has many parts, I would recommend going to the manufacturers website for a parts diagram and listing.

did you get it fixed, I had the same problem but with a different part , I know where your part go's 1st without screw holes go's in the Rear where the laminate comes out and the next one goes on top email me if you didnt fix it yet , I can open mine and get pictures Email me here [email protected] Subject Laminator APL-330U

its from the humidity. the higher the humidity the faster it will fill up.

clean it blow all the dust out clan the coil replace filter

We just brought home a new Royal Sovereign Laminator. Plugged it in and turned it on. It will not stop the loud, annoying beep and is stuck on reverse. It's going right back to the store for a refund. Will not ask for another Royal. If you can't make it right, don't try to sell it!

I would try writing or calling... http://www.royalsovereign.com/customer-support/contact-us.html

You can find the Owner's Manual here: http://www.royalsovereign.com/media/downloads/54/RBC-1003BK_OM.pdf

The good news is that the unit is functioning, it's just counting pennies. I had the same problem with quarters and is a fairly easy fix. I won't get into any disassembly details, but you'll need to gain access to the infrared detectors (mounted to the motor assembly) and possibly the emitters (mounted to the front panel LCD display/push button board). Also, please be careful not the damage the wire harnesses when removing the top cover. Once apart, you can use your cell phone camera (which is sensitive to infrared) to see a purplish/white glow from a healthy emitter. Compare the penny emitter to the others and chances are it will have a lower output level and need replacing. If the penny emitter is strong, then check the detector with any infrared remote control( TV, cable box...) by pointing the IR remote control towards the penny detector and pushing any of its control buttons. This should make the penny amount count up, and fast too, as the remote sends out IR pulses while a button is being pushed. If this test doesn't increment the penny count, then the penny detector needs replacing. But before you do, try this remote control test on another known good detector to verify your findings. Please keep in mind that other malfunctions besides an emitter and detector could be the cause of your problem, but given the FS-4DA circuitry, the odds are extremely high that you have a bad emitter 1st, then a detector 2nd, as emitters are known to degrade over time and especially when continuously powered, as in the case of a switched 'ON' FS-4DA. FYI...IR emitters and detectors can be purchased from Radio Shack. Good luck and take care not to electrocute yourself when powering the unit with its cover removed.

does it have a ground protect circuit on? if it does you have to open and clean it with acetone and a tooth brush or replace the plug. Tony Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/tony_a41fa0b801734e2f

Check the breaker and always use a new capacitor whenever you replace a motor

check the breaker and the plug has a breaker to I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102

Generally speaking these units are not meant to be serviced by the user, If your a pro there are ways it can be done, using specialized equipment. Does the compressor kick on? If so, you don't need freon, take the covers off and clean the radiators inside thoroughly.