Rotel Logo

Rotel Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 40 Products
  • 135 Answers
  • 18K Views

most likely your CD player doesn't support the formatting of the CD you are trying to use.

you didn't mention if this happens to ALL the CDs you try to play or only for specific ones.
if you don't use a copied CD do you still have an issue?

Rotel Audio... | Answered on Apr 05, 2011


I'd call or email Rotel service@rotel.com
Rotel of America
54 Concord St.
North Reading, MA 01864-2699
tel: 978 664 3820
fax: 978 664 4109

Rotel Audio... | Answered on Mar 30, 2011


You cannot fix the receiver unless you are a technician with the proper tools and circuit diagrams. I would think it worth the cost of repair though.

Good Luck
BB

Rotel RX-950AX... | Answered on Mar 22, 2011


If your powered subwoofer could accept speaker level input, like, say a Klipsch KSW-series, you wouldn't need it.

Rotel Audio... | Answered on Mar 14, 2011


Hello
It can be bought from most of the electronic spare part shops near to you. You must have the borken belt in hand as sample. it will help you to choose the correct replacement. OK.

Rotel Audio... | Answered on Mar 12, 2011


Unfortunately, the DVD laser diode is probably faulty. a separate laser diode is used for reading CDs so these still work. The laser unit will require replacing.

Rotel RDV-985... | Answered on Feb 15, 2011


Before we throw in the towel, turn it off and exercise every control a lot of times throughout its range, particularly the Tape Selectors. Sometimes oxides will develop on seldom used controls and their 'normally closed' contacts will not pass a signal.

Rotel Audio... | Answered on Dec 26, 2010


The "no disc" message is a generic one indicating that the disc couldd not be read. This can be caused by a dirty lens (most common) or faulty optics. If you can gain access to the optics, try cleaning the lens using a cotton swab and alcohol. If that fails to resolve the problem, then the optics probably have failed and need to be replaced.

Dan

Rotel Audio... | Answered on Oct 08, 2010


Check the headphone socket if it cuts out the speakers (normal use) when you plug the headphones in. If it doesn't and you have a switch to switch off the speakers when listening to headphones, check the switch. It may be physical damage or dirt causing the problem, or even loose soldering on the headphone socket. But the fact that headphones work shows the main amp is working. Also make certain the speakers are connected properly.

Rotel Audio... | Answered on Sep 28, 2010


In this player the region is hard-coded in the firmware, it cannot be changed by inputting some commands, a new firmware must be loaded.To my knowledge there are no region-free firmwares for this player.

Rotel RDV-985... | Answered on Aug 02, 2010


Incoming from WHAT? Ampifiers accept inputs via RCA connections and send amplified audio to the speakers via the + and - OUTPUT terminals.

I'm guessing your colored wires are from your speakers and that there is a piece of this puzzle we do not see - how the speakers on the deck and in the dining area are wired.

You say, "was working ok previously"... previous to WHAT? Something changed.

You can probably troubleshoot and resolve this yourself.

Set the amp to a medium output level.

If the wires are simply leading to either or both pairs of speakers you could select any two of them and connect them to one side of the amp. Only a pair going to the same speaker(s) will produce sound. Once you identify one pair, the other pair probably goes to the other speakers. Connect them to the other channel output.

The last piece would be to establish correct phasing between the speakers. Bass response will suffer if they're not IN-phase. Play something with substantial bass. Listen closely, then reverse the wires on one side only. Test again. If it IMPROVES you have it right. If it losses bass, put the wires back the way they were.

Rotel RMB-1095... | Answered on Apr 28, 2010


I think the best solution is to remove the jumpers from the Pre Out - Mon In connectors, insert a pair of RCA Y-adapters and plug one end back to the Mon In while the other ends feed the NAD (Page 15 of the manual available at Retrevo.com) . The Rotel's volume and other controls will still be in charge of the NAD.

The manual fails to mention looping the Pre Out back to the Mon In to enable the Rotel's amp to still participate in the program material.

Rotel RMB-1095... | Answered on Apr 10, 2010

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Rotel Experts

 Grubhead
Grubhead

Level 3 Expert

5683 Answers

The Knight
The Knight

Level 3 Expert

76036 Answers

Raj Patel

Level 3 Expert

1023 Answers

Are you a Rotel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...