Roland Popular Questions, Answers, Tips & Manuals

Could you try (1) Temporarily stick a white strip over the sensor where it detects the media or (2) On the length of the media or (3) Even staple same sized white media below the black one which you can un-staple after printing. kindly ignore if these are (s) tupid answers

hi, cyan and black not print in roalnd versa studio bn20 ?

It's doubtful that the LED itself is burnt out, so it's most likely a problem in the circuit. I doubt it will be user-servicable, so take it into the repair shop.

if its less than five years old then you maybe able to order it right from roland , older than that you can always ask them but you might be out of luck , a friend of mine had a problem with his keyboards display too and it turns out it had a external display monitor output on the back, ive rigged him up a small 4 inch tv that plugs right into it and now he can select all his functions using that . works

I would suggest cleaning the input jack, and if that doesn't fix it, replacing the jack.

Contact Roland directly. Speak to their customer service department in your country. I beleive this is the info- http://www.dealerlocations.in/roland-dealers-in-kolkata If it's just a parts availablitiy problem, remember that Roland is a world wide company. Contact Roland in other markets, starting close to you and expanding out. Somebody will have it. I'm in the USA and often source parts from Canada, for instance. If the instrument is truely dead, you can always sell it for parts to other users. Ebay would be a good option.

Hi, I can help you with your question. On the face of the effects, towards the right side, there are three settings that can be adjusted: DRIVE, TONE and VOLUME. The VOLUME knob is your master volume. The expression pedal can adjust volume, but it's output volume is controlled by the master VOLUME knob we just identified. I hope this has helped you, and if it has, could you please click on the "helpful" button ? Thank you!

if your saying the power goes on/off allot then its got to be your power cord or connector in the back , these do have a hard life as these get moved around a bit , its gonna take a pro repair to replace the power connector-but you can buy new cords for them , try to wiggle it to confirm that's it , but if your display just goes on off , this is a software problem as most likely a error in reading the drive

I run wire's from effects to mastering tracks

Contact Roland in whatever country you're in for the service centers in your area. For instance in the USA check this link- Roland Support Service Repair Service Center Locator

Julio, If you already changed power supply and no success, it is probably a bad solder joint on board. I will post a link below that may help or you can try a forum. http://roland.com/support/article/?q=manuals&p=GT-10

PDF]BOSS ME-70 Training Guide - Roland

cdn.roland.com/assets/media/pdf/ME-70_Training_Guide.pdf

AC adaptor. • $418.50 List, $299 MAP ... Connect the ME-70 to power using a BOSSPSA-120S AC Adaptor. 4. Plug a guitar into the ... For illustration only ). 4. Press the ...1. Turn the MODULATION TYPE knob to select a Modulation effect. Do not ... 2. Pressboth pedals down again or press EXIT to return to Manual Mode.Missing: han ‎dots

ME-25 Guitar Multiple Effects Review ' Boss ' Guitar Effects ...

https://www.ultimate-guitar.com/.../boss/me-25_...

Ultimate Guitar Archive Rating: 8.6/10 - ‎135 votes Sep 16, 2015 - Overall the effects are very very full sounding and don't sound too digital by any means. ... With 2 selector pedals, up and down, its a pain in the ? ... Editing the patch is as simple as press 2 buttons at the same time and turning ... If this was stolen I would probably get the ME-70 just because it pretty much ...

Tom Scholz's Guitar Sound - Van Halen Links.com

Your best bet would be to ask Roland. Here is their link- https://www.roland.com/us/company/contact_us/ Roland Company Contact Us Contact Us

Here's the link to the info- http://www.sweetwater.com/sweetcare/articles/roland-td-7-initializing-td-7-restoring-factory-settings

Support Roland Your best bet is to contact Roland support. Here's the link- Support Roland

You should ask Roland Service. Here is the link- https://www.roland.com/us/company/contact_us/ Roland Company Contact Us Contact Us

There may have been a power surge that took out the fuse. At least that's the first step.

1. Make sure that you have the correct power supply plugged in. 2. If you are using the BOSS power supply, it could be defective. Measure the voltage it is producing and make sure it is correct. 3. If the voltage is correct, then the problem is inside the unit, and it will need servicing.

That sounds like a compnent failed in the preamp section. This will not be user servicable and will need to go into the repair shop.