RoadPro Vehicle Parts & Accessories - Recent Questions, Troubleshooting & Support
How to change a turn signal bulb on my 2005 acura tl?
My standard answer for this type of question is that you should purchase a haynes or chiltons manuel for your vehicle, you will find a lot of very good info about many things as well as tips for repairs that will save you time. These can be purchased from most auto supply stores or for a little less money on ebay.
What would cause a 99 Chevy Lumina turn signals to switch from left to right while putting on left one?
this a common problem with all GM cars.. First off, make sure the bulb contacts are free of dirt and corrosion. Make sure the bulb is installed correctly with the electrical contacts in it's proper place.(make sure that the contact from the socket and bulb are making contact to each other). If that does not work, check and make sure that ALL bulbs are good and functioning. Lastly, if none of the 2 above mentioned does not work. You must check for a SHORT TO GROUND. Check voltage. check all related wires for wear, frayed and broken/cut wires.
I just put a new air chuck on my compressor
It's most likely the valve core. Sometimes they get jammed up, especially if you put a brass valve core in a stem that's attached to a TPMS sensor. If the stem doesn't have a sensor in it, then you can remedy this problem fairly cheap (my shop charges $1 for just the stem, but $6 to have it put in). If it is a TPMS stem, then you'll probably have to replace the sensor (last one we had to replace cost $156).
Hope that helps! Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/cameron_463100ffd54b591d
Replace front turn signal light bulbs in a 2000
On top of headlight assembly there should be 2 small metal bars about the size of a pencil. Turn each one and lift both out. Then you should be able to pull entire headlamp assembly out and reach bulbs from rear.
2001 Cadillac Deville Northstar Engine thermostat location
4.6 Northstar V8. It is located on the rear of engine (driver side) in front. It is in the the water pump housing cover. Remove air box and intake tube and bottom radiator hose. 2 bolts(believe 10mm) on thermostat housing. These systems are a little finicky about air pockets....so fill slowly and let run at idle until operating temp and let cool and check level.....fill as needed and repeat if needed.
Peugeot expert central locking not working
A faulty central locking system might be due to several reasons, such as a blown fuse, faulty solenoid, or electrical wiring issues. Also, it's good to remember the fault might not be with the central car locking system but the key fob instead; over time, fobs require battery changes.
What is hashtag
hash·tag
noun
-
(on social media sites such as Twitter) a word or phrase preceded by a hash or pound signand used to identify messages on a specific topic."spammers often broadcast tweets with popular hashtags even if the tweet has nothing to do with them"
-
the hash or pound sign (#)."Hunt mistook an @ for a hashtag while tweeting derogatory thoughts about him"
1944c Furuno radar array won't spin 7 years old. Just beeping
It seems like you're dealing with a technical issue related to a Furuno radar array. If the radar array is not spinning and is emitting a beeping sound, there could be several possible reasons for this problem. Here are a few steps you can take to troubleshoot the issue:
- Check Power Supply: Ensure that the radar array is receiving proper power. Check the power cables, connections, and any fuses that might be relevant. Make sure the power source is functional and providing the correct voltage.
- Inspect Mechanical Components: If the radar array won't spin, there could be a mechanical issue with the rotating mechanism. Check for any obstructions or debris that might be preventing the rotation. Lubricate any moving parts if necessary.
- Connection and Wiring: Examine the connections between the radar array and its control/display unit. Loose or damaged cables could cause communication problems and result in the array not spinning. Ensure all connections are secure and undamaged.
- Software and Configuration: Sometimes, software settings or configuration options can affect the operation of the radar array. Check the user manual or documentation to ensure that the radar is properly configured. Try resetting the settings to default and see if that resolves the issue.
- Error Codes or Messages: If the radar is emitting beeping sounds, it might be indicating an error condition. Refer to the user manual or any accompanying documentation for a list of error codes or messages and their meanings. This could help pinpoint the problem.
- Contact Support: If you've tried the above steps and the issue persists, it might be best to contact Furuno's customer support or a qualified technician for further assistance. They can provide more specific guidance based on the model of your radar array and the symptoms you're experiencing.
Remember, working with electronic equipment requires caution to avoid electrical hazards. If you're not comfortable troubleshooting the issue yourself, it's always a good idea to seek professional help.
What does Fo4 mean on a Vector battery jump box?
The "F04" code on a Vector battery jump box typically indicates a fault or error within the unit or its connections. This error could be caused by a poor connection, a damaged battery clamp, or an issue with the box itself. To help fix the issue, try these steps:
1. Ensure the battery clamps are clean and not damaged.
2. Check the connections between the jump box and the battery terminals. Ensure the positive (+) clamp is connected to the positive terminal and the negative (-) clamp is connected to the negative terminal or a suitable ground location on the vehicle.
3. If possible, test the jump box on another vehicle to confirm it is working correctly.
4. If the issue still remains, consult the user manual or contact the manufacturer for further assistance or information on potential repair options.
Not finding what you are looking for?