Ricoh Aficio - Recent Questions, Troubleshooting & Support - Page 2

1. ATTACHED PRINTER TO COMPUTER AND TURN IT ON 2. OPEN PRINT PROPERTIES 3. CLICK ON SMART ORGANISER, IF U DO NOT HAVE THIS DOWNLOAD AND INSTALL FROM RICHOH WEBSITE 4. CLICK ON ABOUT 5. MOVE MOUSE ARROW KEY TO PICTURE ABOVE TEXT BOX INSIDE BLUE AREA 6. HOLD SHIFT AND CONTROL KEY AND DOUBLE CLICK RIGHT MOUSE BUTTON TO OPEN SERVICE MENU >>>>> DO NOT PLAY WITH ANY OTHER SETTING OR YOU MAY PERMANENTLY DAMAGE UR PRINTER<<<< 7. CLICK ON RESET SC FUSE ONCE ONLY. (IT WILL BE SECOND LINE TOP LEFT SIDE) 8. FROM MAIN POWER SWITCH TURN POWER OFF AND AFTER 10 SECOND TURN IT BACK ON. 9. UR PROBLEM WILL BE SOLVED.

https://printcopy.info/index.php?mod=erc&brand=Ricoh&model=SP100SU&code=SC545

https://printcopy.info/?mod=erc&brand=Ricoh&model=MP1900&code=551

Model No. In Ricoh Aficio sp 1100sf Error Massage displayed (Printer error fuser temp.

TD sensor (Vt low) error 2: K

i have ricoh 3010 model-he say remove the paper from internal tray.but there is no paper please guid me with video

Hi jimsal,

Welcome to Fixya. Yes Diagnosis is correct because SC670 is a common error on this machine.

SC670 mistake Engine Response - After powering on the machine, a response is not received from the engine within 30 second. Which means when the main power is turned on or the machine starts warming up from energy-saving mode, the controller does not receive a command signal from the BCU. There could be few possibilities that you need to check and diagnose

Reasons:

- Loose connection
- Defective controller
- Defective BCU

Troubleshooting:

- Turn the main switch off and on.
- Check the connection between the BCU and controller.
- Replace the controller.
- Replace the BCU.

Here's the illustration of the controller:


To reinstall the controller board into the printer push the bottom center area of the board

After replacing the BCU or controller, remove the NVRAM on the old board and put it on the new one.
This should be the series of troubleshooting. Unfortunately, this is not an easy fix. If you do not have any repair experience, i would advise you to call a Ricoh professional so that he could take care of the problem.

Thanks for using Fixya.

that is software program error. u need to update firmware

GoDaddy Customer Care Number

Under printer check book unmark Use printer offline

Dear kishorkamble, We fixed this error, which happened in another model (Aficio MP-5500), by configuring two options: 1. Activating SNMP protocol. Menu Configuration -> Network -> IPv4 2. Activating RSH/RCP protocol. Menu Configuration -> Network -> SNMP I hope it may be useful. Yours sincerely, Bruno Coutinho

How to clear Error sc565 Ricoh Printer

"Replace Print Cartridge" remains in display. Then a new AIO cartridge must be installed. This feature is a safety measure to prevent the used toner tank from becoming full (there is no toner overflow detection mechanism).

Enter and exit service mode

This is a message on your PC...not the machine itself obviously? Was this scanner ever configured to work on your PC? If not, then follow this link to my comments to someone else about this machine:

http://www.fixya.com/support/t1718617-ricoh_1515mf_scanning

Hi, please do not use an SD card that has been used in a computer, use an original SD card meant for this particular printer. i.e. for MP C3500/4500

Go to the following link. At least this is where I found the latest driver for Mac OSX 10.5+
http://www.ricoh-usa.com/downloads/downloads.asp?tsn=Ricoh-USA&path=http://support.ricoh.com/bb/html/dr_ut_e/rc2/model/c30e/c30een.htm

SC565 *Heat lamp consecutive on error - Broken main fuser connection *Heat lamp consecutive on error - Check HR thermistors with SP1-106 001 (ctr) and 002 (ends) *Heat lamp consecutive on error - Heat roller lamp defective *Heat lamp consecutive on error - Power Supply defective

unplug printer, wait minute, plug in, should reset.
check Ricoh website to trouble shoot if does not reset.

https://www.youtube.com/watch?v=RpUDjiaU4yc