Rheem Popular Questions, Answers, Tips & Manuals

recently installed?

Brian sounds like it's Leaking From Anode rod.... Check here.... https://lildutchuncle.com/rheem-water-heater-leaking/

The three most common reasons for this happening to you are 1) a defective gas valve, 2) a rusty thermopile, and/or 3) the automatic shut-off not working as it should. So, the most common reason for many people having this problem stems from having a gas valve that is not working as it should. When your gas control valve is faulty, it will mean that your burner is not going to be igniting as it should-or at all. Something that worked for me one time was to turn the Temp all the way down then all the way to Max a couple of times..gradually. Why it worked I don't know. Got a couple more years out of it though. Good luck! Best to you.

there is pressure adjustment, just temp. water pressure in + water pressure out

Posted to the category Cars and Trucks but appears to be heating. All questions need FULL 'make model (what it is)' as first 3 words. Contact Rheem direct and claim a warranty replacement of the thermostat or free service advice. Did you try a power reset? https://www.google.com/search?q=UMC-117 ..

The burner cover plate for your Rheem RRNL-B030JK08E unit can be obtained from an authorized Rheem dealer or distributor. You can visit the Rheem website to locate a dealer or distributor in your area. Alternatively, you can contact Rheem customer service for assistance in obtaining the burner cover plate. Be sure to have the model and serial number of your unit available when contacting Rheem customer service.

Question edited for clarity and spelling of 'capacitor'.. Question moved from Televisions to Rheem A/C. When a start/run capacitor fails, the fan doesn't turn at all, it will just hum. Try a full reset of the system. Disconnect the power at the breaker for at LEAST 2 hours, or preferably overnight. It resets the logic board and resets all the relays. If that doesn't work, you need an A/C Service Technician.

this from Rheem error codes Error Code 60 FAULT = Hot Water Temperature Abnormality

1. Press the Power button to clear the Error Code. If Error happens again:
2. Ensure water heater inlet and outlets are open and water is supplied to the water heater.
3. If Error happens again:
4. Ensure water heater inlet and outlets are open and water is supplied to the water heater.
5. Check the pump operation.
6. If it doesn't work, ensure wiring connections to pump.
7. If even supply power to pump and doesn't run it, replace the pump.
8. If Error happens again:
9. Verify recirculation loop length is within specification. Air purge is not enough.
10. Too much restriction on recirculation loop.
11. Return loops are clogged.
12. Check the recirculation loop condition.

moved yah from cars to HOME HVAC the maker RHEEM has a web site. and has full documentation on that, and more. go there get it and see it. if using non RHEEM stat , that takes a book on that stat too. and is not too hard to figure out.

Hi, From what I'm seeing this means that there is a bad part within your furnace and it needs to be replaced. It might be the thermostat. You might need to reach out to a local HVAC company to diagnose the issue in person. Thank you.

Rheem furnace error code 68 is a mechanical relay system which signals the blower motor to stop because it has not received a signal from the thermocouple. Jul 20, 2022

Rheem furnace error code 68 - HVAC Contractors

Motor Power And Communications Issues (Fault Code "68")

ManualsLib https://www.manualslib.com > Rheem-96v-Series Motor Power And Communications Issues (Fault Code "68"); Line Voltage And Low Voltage Connections To The Communicating Motor - Illustrations - Rheem 96V Series ... ..

check wiring

https://www.youtube.com/watch?v=u6w88TXMbg8

https://parts.rheem.com/contactus .

Question moved from Kitchen Ranges. You need a High Altitude Conversion Kit from the maker. Then you need a gas registered technician to fit them and adjust. Standard altitude is up to 2,000 feet above sea level, https://www.google.com/search?q=gas+water+heater+setting+for+altitude+above+sea+level ..

here are codes.. Personally I would check my paper work from unit to if is covered under warranty.. Good Luck https://www.manualshelf.com/manual/rheem/xe50t12cs45u0/instructions-assembly-english/page-19.html

if system is new call whomever installed it and it repaired under warranty. there are several reasons unit is not producing hot water. First thing I would check is temp setting. Again call for service under warranty.

the gas valve can be replaced, but you will have to pay for installation. this is not a DIY. You can throw money and parts at it. Personally I've replaced my water heater at the first sign of problems. Are they inexpensive no If you furnish model number I can look further.

check flow switch if not activated wont call for heat

Instructional videos, Honeywell instructions and wiring and a link to Just Answer with wiring help.https://www.google.com/search?q=wiring+Honeywell+RTH5160Dhttps://www.justanswer.com/hvac/bzpmd-purchased-new-honeywell-rth5160-non-programmable.html..