Remington Recent Questions, Troubleshooting Help & Support

Register it, wait a week and return it for repair under warranty. https://remingtonpowertools.com/product-registration/ ..

bar oil only

I've written up a complete step-by-step tutorial on how to replace the battery on a Remington MB-300 Beard trimmer, which includes how to reassemble it: John Fixes Stuff How to Replace the Batteries in Remington MB 300 Beard...

https://www.google.com/search?q=Scc-100r+Remington&oq=Scc-100r+Remington&aqs=chrome..69i57&sourceid=chrome&ie=UTF-8

You might try the following

https://www.worx.com/leafpro-universal-collection-system-wa4058.html?gclid=Cj0KCQjwoJX8BRCZARIsAEWBFML3DbNBxST-tes-ZT4MQTUXbkCFx_5LyueLDfUwqfXsm-C4N32iUesaAtoiEALw_wcB#

There is a hidden screw just above the charge jack that holds the top cover in place. Remove the plastic plug that hides the screw, unscrew the screw, and pry off the cover. My unit would not charge anymore. I think the charging electronics are poorly designed. I extracted the battery and electronics leaving only the motor, then wired the motor directly up to a 5 volt battery pack. It now works great!

First check the fuse.

Remington Pole Saw Carbon Brushes If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature! Remington carbon brushes on E-bay Search for: Remington Pole Saw 8 AMP Carbon Brush

check for a roll pin in the gear or shaft that has sheared off check that the square end of the drive shaft is not rounded off or that the square drive in the gear is in fact locking on the drive shaft and not turning from worn out

Not sure why you posted this in a health forum, but see this manual for how the spring fits. https://www.remington.com/sites/default/files/documents/e6206rem_Q7.pdf

Have someone tried bulk ammo deals with free shipping at Ammo Board? https://www.ammoboard.com/

Remington recall contact information on the internet: https://www.remington.com/support/safety-center/remington-model-700-and-model-seven-notice

To change that trigger switch on a Remington saw, you need to open up the two handle halves and expose the switch. The wires are just "poked" into the switch, so you can make a tool to release them. I used a 1/16" diameter short length of wire and flattened about a 1/2" of it on an anvil. Push it in next to the wire and the wire will pull out, wiggle the tool a bit and it will pull out too. Push the wires into the new switch and put it all back together. The switch is probably a #077525S ...seen them out there for $8 to $15.

No threads, it snaps in and can be snapped out if you are careful.

How to Replace Remington Electric Shaver Batteries You may need to solder the batteries. https://www.amazon.com/Shaver-Replacement-Battery-AA-NiMH/dp/B00R8IZ2LY

Okay here is the Fix for the Remington Pole for the remington saw. Lowes has a plumbing part that will work as I just purchased it 12/2010 The part is by GENOA and its a 3/4" pvc Union and the threads match. Its Lowes part 98996 and its < $6.00

1. Try a penetrating oil, like product "deep creep". WD-40 is not a penetrating oil, it is a water displacement oil. Proper penetrating oil should work. 2. Try soaking in house hold, distilled vinegar, the really cheap stuff. For a few hours, and try again.

Looks like there should be a power button below the digital readout for the temp. There are a + and a - and a power button I believe.