Razor Sport & Outdoor - Others - Popular Questions, Answers, Tips & Manuals

Find out whether it is 6 volts or 12 volts and there should be two wires that feed the motor either cut or splice and attach another set of wires with fuse in the line (simular to jumper cables) raise the back tire so it does not touch the ground and place jump wires to the negative and positive of the battery.
If the motor moves in either direction without blowing the fuse the motor is good if not then its bad. Uses the same amperage fuse

replace the fuse with a bulb of the same voltage rating like 12v bulb it will take the spikes but it might allow her to over load it too an motor git warm then the thermalfuse might kick in . worn out motors an batteries do this stuff

Change the motor or the pulley

Razzor was purchased by Polaris, contact nearest Polaris dealer

I had this same issue with the Razor E100. I couldn't even remove the plastic cap it was so recessed. Here's what worked. The value comes from the factory very recessed in. It's so far in it's hard to remove the cap with your fingers. You'll need to get the value loosened up and pushed out a bit. You will do this from the other side of front wheel using the hole. The value can be manipulated slowly to stick out about an inch from the plastic wheel. It takes some time and patience. First, you’ll need to turn the scooter over and rest it on the handle bars and back of the deck. Put a towel or flatten box under it if working on a rough surface to protect the scooter. Then used the supplied Allen wrench or similar object by putting the long end of the wrench into thru the opening hole on the other side of the wheel. Wedge the edge/end of the wrench against the value from the other side of the wheel and push hard to loosen up the value. This takes some time. Do this on both sides of the value and also against the center of the value. It took me about 5 mins of careful pushing. Eventually you will be about the get the value to almost a right angle from the wheel and sticking out about and inch. Then remove the plastic cap. This will give you room to attach a bike pump. I actually had to push the value back in a bit once finished so the wheel could turn freely. It will work, just be patient and forceful. Take your time.

The Switch can be almost any but the lighted switch has to be a compatible 24vdc lighted switch. As seen on this web page. SWT-105 Razor E100 and E125 Electric Scooter Parts ElectricScooterParts com

using a Normal bicycle pump

Razor E100 batteries are easily replaced & there are guides on how to this on razor.com, genuine Razor batteries are available at most good Razor product stockists.

There are a few components to check when diagnosing electric scooter issues.

1. Batteries
2. Wiring
3. Controller
4. Throttle Assembly
5. Fuses

Once you inspect all of these for damage, you can test your motor and batteries, by bypassing the controller, and directly hooking the batteries to the motor. If the motor spins very fast, then you have good batteries, and a good motor. The controller will need to be replaced. If your motor spins slowly, you could require new batteries or Controller, or battery, depending on the results.

You can find replacement parts and service locator here.

urbanscooters.com/partsforscooters

if your gonna write something that can't be answered atleast accept me so i get paid for my time unless you can explain in detail what your problem is

Probably around 12 volts. It depends on what your battery (ies) put out but I thinkit's most likely 12volts.

Get a replacement holder at the Radio Shack ... you will have to modify to install in all probability.

Hi:
I have a rascal 3 wheel chair and the tire is flat on back, how do they come apart for repair, thanks.
Leroy

Blade E scooters are products of China, so you would need to contact the manufacturer to acquire the factory wiring diagram. Usually the manufacturers are very allusive and hard to contact, so if this is the case with your scooters, you can try this online scooter parts store. They have a "find a repair shop" feature that will provide you with addresses and phone numbers of shops near you that will help you.

http://urbanscooters.com/partsforscooters

-Jackson
http://urbanscooters.com/

in order for the scooter to go you must already be walking with the scooter. so hold down the throttle and start to push (kick) the scooter.

hooperimports.com/showpages.asp?pid=1013
they have wiring diagrams and information on how to wire chinese import engines and for more info contact http://tinyurl.com/m7ghqz

I have the aggressor scooter as well. You don't need and probably will be hard to find the toggle switch you mention. Just go to Radio Shack or Frys with the switch and find the one that match the power rating and profile of the old switch.

Hi Marci. Take the scooters, batteries and all plus your charger to any autozone store and ask them to test your batteries and charger for you. They have the equipment to do these tests and they do it for no charge, they are great.

if you remove the resistor and take it to an electronics shop they can tell the rating from the colored bands that are around it.