Quinton Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

14 Products
10 Answers
3K Views

0answers

We have a Clubtrack and there is a delay when pressing the button to incline, and decline. It will only go up to 4.0 and stop raising, even though the display goes up to the max of 15.0 incline.

Read full answer

Be the first to answer 1/16/2018 3:24:03 PM • Quinton CLUB... • Posted on Jan 16, 2018 • Be the first to answer

0answers

TREADMILL

Read full answer

Be the first to answer 6/14/2017 12:24:03 PM • Quinton... • Posted on Jun 14, 2017 • Be the first to answer

0answers

We have a Q4500 system interfaced with a Quinton Q65 treadmill. This system has always functioned well, but now for some reason the maximum TM speed that can be generated is 5.2 km/hr (3.2 mph). We'

Read full answer

Be the first to answer 6/8/2017 3:27:03 PM • Quinton Q4500... • Posted on Jun 08, 2017 • Be the first to answer

tip

How To Calibrate the Lift Motor on Quinton ClubTrack Treadmill

The following describes the steps required to calibrate the lift motor on a Stairmaster (Quinton) ClubTrack.

Enter service mode on the treadmill by using the following keys at the same time:
- Faster - Slower - Stop Belt
Allow the lift motor to free spin by removing the bolts from the metal block on the jack screw.
Press the up arrow on the control panel until the incline is at 5% then press the down arrow and take it back down to 0%. This will allow the lift motor rheostat to find its range.
Spin the metal block on the jackscrew to allow 1 - 1.5 threads to be exposed from the top. Secure the lift motor back to the frame by inserting the 2 bolts through the bracket holes and into the metal block. NOTE: Double check the spacers on each side to make sure they are flush.
Run the treadmill incline up to 15% and check the jackscrew to verify it has not bottomed out before reaching 15%. There should be around 4 - 6 threads exposed. Bring the treadmill back to 0% where there should be the same amount of threads exposed from the top of the jackscrew. If you see the correct amount of threads the lift motor is calibrated.

NOTE: If there is an error on the display panel, ex. E211, you need to manually turn the jackscrew back to 0%. To perform this unscrew the 2 bolts from the bracket securing the metal box and jackscrew allowing it to freespin. Use a shop rag or towel to wrap around the jackscrew to prevent damage to the threads. Using a pair of pliers (channel locks or vice grips recommended) manually turn the jackscrew back to 0%. Once this is accomplished run through the above steps to perform the calibration. Quinton Treadmill Support How To Calibrate the Lift Motor

Read full tip

on Mar 10, 2015 • Quinton CLUB TRACK Treadmill

0helpful

1answer

How to change a walk belt on a stairmaster treadmill

http://www.sportsmith.net/images/product_support/quinton/Manuals/ClubTrack%20510%20-%20612%20Service%20Manual.pdf This is the link to a service manual for the 612.

Read full answer

2/4/2015 10:49:00 PM • Quinton... • Answered on Feb 04, 2015

0helpful

1answer

Tred mill gradient motor wont start

Likely motor controller, although it could be motor windings

Read full answer

7/17/2014 10:09:15 PM • Quinton St55... • Answered on Jul 17, 2014

0answers

Belt does not go

Read full answer

Be the first to answer 6/13/2014 3:10:38 AM • Quinton St55... • Posted on Jun 13, 2014 • Be the first to answer

0answers

Q4500 not putting treadmill into bruce protocol.

Read full answer

Be the first to answer 9/13/2013 5:47:55 AM • Quinton Q4500... • Posted on Sep 13, 2013 • Be the first to answer

0answers

I need q4500 stress test monitor service manual

Read full answer

Be the first to answer 9/6/2013 4:31:27 AM • Quinton Q4500... • Posted on Sep 06, 2013 • Be the first to answer

0answers

I have a treadmill stairmaster clubtrack-612plus,

Read full answer

Be the first to answer 8/16/2013 10:32:02 PM • Quinton... • Posted on Aug 16, 2013 • Be the first to answer

0helpful

1answer

PLO5 error message on Quinton Clubtrack treadmill

Try to clear the error message. God bless you

1 )Locate the reset switch on the underside of the treadmill console. Usually the button is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.

Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.

Press enter twice more. The letters "SS" should appear on the screen. When this happens, press the start/stop key. Making sure to keep well away from the tread, press enter to start the treadmill. The treadmill will start on its own. The treadmill will stop on its own after a few seconds. When it stops, press the power key two times. Remove the safety key and put in a safe place. Your treadmill is reset

Read full answer

1/27/2013 8:58:45 AM • Quinton... • Answered on Jan 27, 2013