Quantum Health & Beauty - Page 3 - Recent Questions, Troubleshooting & Support

0helpful
1answer

How do i recharge a dead battery for my quantum motorized wheelchair?

First ensure the battery is completely discharged by using a voltmeter or other suitable method. If the battery really is dead it should be charged with a suitable known good battery charger for the required time, allowed to stand a few hours and then tested by putting it into use or employing a suitable method of testing. All disability scooters and electric wheelchairs arrive with a dedicated battery charger which should be used if possible, though these sometimes fail and need replacing. In that case other methods of charging can be employed but purely on a temporary basis as there are safety concerns with battery charging. If charging the battery does not work, it might need replacing and/or there might be a fault with the wheelchair.
2/25/2017 5:28:12 AM • Quantum Health &... • Answered on Feb 25, 2017
0helpful
1answer

Where are the Quantum 600 Fuses Located?

Ron, With a gifted power wheelchair, the usual culprit is a pair of dead batteries usually size 22NF deep cycle batteries. The pediatric chair may have U-1 (35 amp hour batteries) There are fusible links connected to both batteries at the + terminal. There are additional fuses under the rear cover in booted holders in the belly area in the rear near the controller. These power take off harnesses are fused but probably do not relate to your primary dead battery problem. Remove the front cover of the base and pull out the battery tray. Remove the batteries, test, and replace. The owner's manual can be found here. It also includes basic service. Hope this helps. http://www.pridemobility.com/pdf/owners_manuals/us_jazzy/us_q600_series_om.pdf
7/24/2016 11:37:03 PM • Quantum 6000... • Answered on Jul 24, 2016
0helpful
1answer

How to change the battery

This should cover it for you. Seems to be a lever under the seat that will then allow you to remove the seat and cover,. 26182881-h3gmruk4y5pvvzbyocke3n3a-1-0.jpg 26182881-h3gmruk4y5pvvzbyocke3n3a-1-2.jpg
5/2/2016 7:47:48 PM • Quantum 6000... • Answered on May 02, 2016
0helpful
1answer

My quantum wheel chair is stuck on charging mode but is not plugged in? how do I reset?

hi disconnect the battery terminal for 5 or 10 minutes and it might reset .......good luck
4/29/2016 4:57:53 PM • Quantum 6000... • Answered on Apr 29, 2016
0helpful
1answer

When I go To move the chair comes up with error 107. , charger inhibit . I disconnected the charger. What can I do next

after do a test restart the chair. make sure both freewheel levers are locked in drive mode (hard to push), restart, make sure your connections are good, to the motors and brakes. what kind of Joystick is this? I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489
4/7/2016 8:59:05 PM • Quantum 6000... • Answered on Apr 07, 2016
0helpful
1answer

It started running lower and lower even thought it was fully charged, now the last couple of day I've been getting bus overload and it will not charge

Quantum 6000 - Pride Mobility Products

www.pridemobility.com/pdf/owners.../au_q6000_om.pdf
Pride MobilityQuantum 6000 .... WELCOME to Quantum Rehab, a division of Pride Mobility Products ... The symbols below are used on the power chair to identify warnings, .... Lowpressure may result in loss of control, ... If you must stop, start up again slowly and then accelerate .... Avoid tall grass that can entangle the running gear.

[PDF]Quantum 6000Z - Pride Mobility Products

www.pridemobility.com/pdf/.../intl.../au_q6000z_om.pdf
Pride Mobilitythis power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the power chair to identify ... NOTE: The Quantum 6000Z and its components are not made with natural ..... Turn the adjusting screw to raise the front of the armrest or to lower the front ...

Pride Mobility Quantum Q6 Edge (Power Wheelchairs ...

www.usatechguide.org/itemreview.php?itemid=1626
35 posts - ‎30 authors
2/5/2016 1:46:35 AM • Quantum 6000... • Answered on Feb 05, 2016
0helpful
1answer

Push power button wont go but all the adjustments legs back tilt works

quantum 600 wheelchair troubleshooting Questions ... - Fixya

www.fixya.com > Forum > Tags
quantum 600 wheelchair troubleshooting chair won't go all i get form joystick is a picture of a ... around in a square there should be a rest button on the rear of the chair ,push ... Question about 600 E Electric Wheelchair - Used Power Chair.

[PDF]Pride Quantum 600 Owners's Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600%20Owner's%20M...
Quantum 600 .... The symbols below are used on the power chair to identify warnings, mandatory actions ... Pride will not be held responsible for injuries and/or property ...complete stop by releasing the joystick, then push the joystick forward slightly to .....breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600E Owners Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600E%20Owner's%20...
Quantum 600E .... The symbols below are used on the power chair to identify warnings, mandatory ... chair. Pride will not be held responsible for injuries and/or property ... complete stop by releasing the joystick, then push the joystick forward slightly to ..... breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600 Series - Pride Mobility Products

12/30/2015 1:01:41 AM • Quantum 600 E... • Answered on Dec 30, 2015
0helpful
1answer

What is error #35?

hi Lizy, there is no such error as 35 ? are you sure it's no flashing 3 ? Regards Rob
10/23/2015 9:32:53 PM • Quantum 6000... • Answered on Oct 23, 2015
0helpful
1answer

How do you reset the quantum Q6 chair

hi you find your manual here, this reset ?/ this is mentioned in the manual /// http://www.pridemobility.com/resourcecenter/Downloads/Product_Owners_Manuals/product_owners_manuals.asp Regards Rob
7/20/2015 2:18:06 AM • Quantum Edge 6... • Answered on Jul 20, 2015
0helpful
1answer

What is error code 251

If you are using a diagnostic/programmer box to get this fault code you need to look in the manual that comes with it for an explanation of the code.
6/16/2015 8:27:31 AM • Quantum 600 XL... • Answered on Jun 16, 2015
Not finding what you are looking for?
Quantum Logo

65 questions posted

Ask a Question

Usually answered in minutes!

Top Quantum Health & Beauty Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66979 Answers

Jesse Walters
Jesse Walters

Level 2 Expert

337 Answers

jws1013

Level 3 Expert

1713 Answers

Are you a Quantum Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...