Python Logo

Python Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 61 Products
  • 263 Answers
  • 55K Views
0helpful
1answer

Car wont start

Okay?
3/6/2013 5:06:23 PM • 991 Responder... • Answered on Mar 06, 2013
0helpful
1answer

How to rest remote474p2

Reset? What's the problem?
2/7/2013 5:24:59 PM • 426P 460HP... • Answered on Feb 07, 2013
0helpful
1answer

Set up the car remote

A 7701P is a remote transmitter. It is not an alarm. You must know the alarm's model because different models have various ways of programming transmitters. In other words, you do not program the 7701P. The frequency is already fixed. You must program your security system to teach it that transmitter's code. Look up the manual for your security system. Instructions will be there. This typically involves turning the ignition on/off a specific number of times and pressing a valet/programming button (or switch) a certain number of times and then pressing a button on the transmitter.
2/1/2013 2:37:19 AM • 990 And 950... • Answered on Feb 01, 2013
0answers
0helpful
2answers

When i try and use the remote start, it doesnt

The parking lights will also flash a number of times to inform you of the error. The most common causes of the error are neutral safety shutdown (7 flashes). This is the toggle switch under the dash. Locate said switch and toggle it to the on position. Six flashes is the hood pin switch. Locate the switch under the hood and make the necessary adjustment so the pin makes contact with the hood when the hood is closed.
1/23/2013 4:25:05 AM • 991 Responder... • Answered on Jan 23, 2013
0answers
0helpful
1answer

Remote start python 533 attempts to start the car, shuts off, then on a again, does it 3 times, then stops

There are three possibilities for the situation you are describing especially if the vehicle has been cold for a while. The first possible cause occurs when the smart tach feature is used. In this case, the 533 is not receiving the proper signal from the vehicle that shows the engine is running. The remedy for this problem is to connect the tach wire from the 533 a proper tach source. The other two causes occur when the smart tach feature is not used and the tach wire is connected. If the tach wire is not connected to a good source for the tach signal in which case the wiring will need to be corrected. Otherwise, the tach signal will need to be relearned.
1/17/2013 4:20:55 AM • 533 2way... • Answered on Jan 17, 2013
0helpful
1answer

My python 1600 wont arm

check battery in remote if good then maybe its in valet mode if so go to viper dealer If you need further help, I’m available over the phone at https://www.6ya.com/expert/stephen_fa62cb6d50fe05e8
11/11/2012 1:42:29 AM • 1401 Remote... • Answered on Nov 11, 2012
0helpful
1answer

How can I find a users guide for a Python 473P remote starter?

473P is the part number of the remote. 473P is the original remote for a Python1200XP alarm. I have the users guide.
8/21/2012 1:33:25 AM • 473P 3-Button TX... • Answered on Aug 21, 2012
0helpful
1answer

Remote Starter problem

Sounds like the immoblizer bypass is malfunctioning or, the pellet (resistor) in the ignition key itself is wearing down.
8/14/2012 9:44:47 PM • 473P 3-Button TX... • Answered on Aug 14, 2012
0helpful
1answer

I can only start with the remote. Just bought the car. At 1st I could start it w/o remote.

Sounds like you need a new key cut and programmed to your car.
8/14/2012 11:33:41 AM • 473P 3-Button TX... • Answered on Aug 14, 2012
Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Python Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Python Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...