Psi Recent Questions, Troubleshooting Help & Support

• TRY HUSKEE OR HOME DEPOT

Jump starters are usually imported generic items label engineered without much of a spare parts service. You might be lucky if you approach the supplier but most likely not. You could try repairing the compressor. They are quite simple and might even only need a squirt of WD-40 to make the valves work again and the piston to start pumping. In spite of there being no lubrication system they usually give good service and would need extensive use before they wear out. Compressing humid air would create a little water which would provide a little lubrication...

https://www.google.com/search?q=3+amp+250+volt+fuse Like that? ..

Question edited for clarity. Parts suppliers including the maker. https://www.google.com/search?q=portland+1750+psi+parts PORTLAND 1750PSI ELEC PRESSURE WASHER Item# 63254 Legacy UPC: 792363632553 ' UPC: 193175343741 Part# Description Diagram Ref# Price 603070 WAND ASSEMBLY W/ NOZZLE 29A-30A $8.93 603071 GUN ASSEMBLY 31A $11.80 603072 HIGH PRESSURE HOSE ASSEMBLY 32A $15.20 Legacy UPC: 792363632546 ' UPC: 792363632546 Part# Description Diagram Ref# Price 15588 EXTENSION WAND W/NOZZLE 26A/28A(NEW) $9.74 15797 HIGH-PRESSURE HOSE 31 $16.00 15851 SPRAY GUN 29 $16.80 15866 DETERGENT BOTTLE 30 $3.68 PORTLAND 1750 PSI 1.3 GPM Electric Pressure Washer Item# 63255 Legacy UPC: 792363632553 ' UPC: 193175343741 Part# Description Diagram Ref# Price 16023 WAND 121 $4.87 16024 NOZZLE 120 $2.98 16025 SPRAY GUN 122 $15.15 16026 DETERGENT BOTTLE 124 $2.87 16027 HIGH-PRESSURE HOSE 123 $18.94..

Hi, that selection must cause too much internal pressure for certain parts of your device to handle so the leak occur to ....let off a little pressure. Please work with Greenworks to find out whether you need to replace a part of your device to overcome the leak. Their number is 1-888-909-6757. Thank you.

A flooded engine will not start even with starter fluid.

You need to get the cylinders dried out and try starter fluid alone by draining the fuel from the carburetor bowl and pinch off the fuel line at the carb inlet. Then remove spark plugs and crank engine for several seconds to dry out the cylinders.

Next, reinstall spark plugs and remove the air filter. Leave fuel line pinched off. Set 3/4 throttle (choke off). Then spray a 1 second burst of starter fluid directly into the carburetor throat. Don't bother with the air filter and promptly start the engine.

Replace the seals.

Impossible to answer definitively without maker and model, but this says SAE 10W-30. That is a powerful industrial machine! https://www.google.com/search?q=3100+psi+power+washer+what+kind+of+oil& ..

Several sold in the last two years are not available now. Might be able to offer to purchase a copy of the manual only from a seller of the the power washer. https://www.granstore.xyz/pressure-washers-c-1_2_970_978/hyper-tough-1800-psi-electric-pressure-washer-model-5100219-new-p-6931.htm?language=en

Hi Scott,check this link out on your wheels. Pressure washer replacement parts repair kits for Excell devillbiss...

Most pressure cut off switches have an adjustment screw on them where you can dial in the cut off/turn on pressures. Take a look and see if you have the adjustment screws. If you have the switch model, you can try looking up online to see how to make these adjustments.

if properly assembled and properly used then return it for another or refund

with a printer ...first you have to find the manual. try google

Put amp meter to test motor draw and test capacitor as well

Pop off valve? If it is the unloader valve that is venting the air, the discharge check valve is leaking and has to be replaced.

This usually occurs when the motors internal thermal / amp breaker opens due to overload or weak breaker. Use an amp gauge to test for too much amp draw. If amp draw is normal, then problem could be the in-tank check valve leaking pressure back to the pump overloading the system, or weak capacitor or weak breaker. Bypass the breaker temporarily if the amp draw is normal to test system. Good luck

Please clarify what your question is. Thanks

replace the pressure regulator/ control unit

really? Bleed the water line b4 you start.