Pride Mobility Products Logo

Pride Mobility Products Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 74 Products
  • 818 Answers
  • 58K Views

MANY HAVE A BAR THAT WHEN THEY NEED PUSHED BY HAND IT DISENGAGES THE DRIVE .

Pride Mobility... | Answered on Mar 06, 2019


WELL POSSIBLY IF WE KNEW FOR WHAT BUT ALAS WE DO NOT

Pride Mobility... | Answered on Mar 06, 2019


SORRY BUT WE (FIXYA) DO NOT SEARCH FOR PARTS .FOR ANY ONE . CALL YOUR LOCAL REPAIR SERVICE .

Pride Mobility... | Answered on Feb 15, 2019


this could mean the scooter is not in drive try the free wheel lever first.

Pride Mobility... | Answered on Feb 14, 2019


More than likely it has a bad battery or cell in the battery even though it shows a full charge. Once under a load the power drops below 17 volts which shuts the unit down momentarily. Then when it powers back above 17 volts because you have the throttle partially depressed it trips the code 6. Have the batteries load tested and you will see one is bad.
Solution: new batteries

Pride Mobility... | Answered on Feb 05, 2019


There are only three wires for this. either the wire is broke, or the switch.

Pride Mobility... | Answered on Jan 20, 2019


You have a problem in the throttle/speed potentiometer. You will need to contact a dealer in your area to get the part.

Pride Mobility... | Answered on Oct 20, 2018


The best thing to do in this situation is to call the vendor and have them repair it under warranty. There should be no charge for this service since the chair is brand new.
There are some checks you can make to avoid a service call. You have checked the batteries and hopefully the chair is plugged into the wall outlet. It is possible that something got disconnected under the chair. To check this you need to flip the chair over on its side or on its back since the leg rest scissor mechanism is extended. Look for any plugs that have come apart at their connections. Check for a pinched or binding scissor mechanism or tilt frame parts.
You should not attempt this at all if you cannot safely move a large piece of furniture. Perhaps a friend or relative may be able to help.
Insist that the vendor honor their warranty commitment ASAP. If you paid with a credit card, you should contact your credit card company to put the amount in dispute if the vendor is unresponsive. Hope this helps.

And you can troubleshoot with the below instructions if it with also help



things you'll need:

* Pride chair Owner's Manual
* Screwdriver
* Wrench
* Pliers

Instructions


Look at the chair's electrical plug, as the chair most likely became unplugged or the plug is not fully connected to the outlet. If this is the case, securely reconnect the plug.

Check the chair's connections. The electrical connections under the chair could be loose or connection cables could be pinched or bent. Tighten loose electrical connections with a small screwdriver and straighten bent or pinched cables.

Check the chair's transformer, motor and relay box under the chair as a malfunction in any of these could cause the chair to stop working completely. The hand control used by the operator to change the chair's position may also be malfunctioning.

Test the chair's wood frame, bolts and lift frame. Loose wood frames or bolts, overly tight bolts or the lift frame rubbing against the wood frame will all cause the chair to squeal.

Lay the chair on its side and check the wood frame and t-bracket. If the wood frame is rubbing against the lift frame or the t-bracket is cracking, you could hear popping noise. The t-bracket is the metal frame on the underside of the lift chair.

Check the dual motor timing if the chair will not recline all the way. The motors' timing could be off which would stop the chair from completely reclining. Put the chair on its side and remove the motor and plug it in. Use the hand control to turn the motor on and let it run until it stops on its own. Screw the push tube, located to the right of the drive tube where you just removed the motor, until you feel it bottoming out. Turn the push tube back two turns and grab the push tube. Turn the unit on with the hand control and allow the push tube to move away from the metal casing. Push the pin at the back of the push tube and reinstall the motor. This should re-time the motor.

Look at the wood frame, seat foam, leveling legs, motors and bolts if the chair is crooked. The wood frame could be twisted, the seat foam may be broken or misshapen, the leveling leg may need adjustment, the motor could be timed incorrectly or the bolts could be loose. If all looks in order, make sure the ground under the chair is level.

Unplug the chair before you begin fixing the chair.


Restore power to an inoperable lift chair. Ensure the circuit breaker box is connected to the electrical outlet. Make sure the external transformer is plugged directly into an electrical outlet.


Fix a Pride lift chair that only operates in one direction. Use a cotton swab to remove dust and debris from the toggle switch on the hand control. Flip the toggle switch back and forth to loosen any remaining debris which may be causing an obstruction.


Fix inoperable heat and massage features. Check the LED lights on the hand controls; the LED display is not lit, hand-tighten the connection between the hand control and the lift chair. Make sure the the heat and massage units are properly connected to the back of the lift chair.

Pride Mobility... | Answered on Jun 03, 2018


Hi a load tester will give u an accurate reading on there condition available on E/BAY COST APROX $35 ...test one battery at a time tester is 12 Volt :::::With a car battery u can check each cell separate with a Hydrometer..your batteries r sealed : u can't use one .cheers
img_20180118_224641092-ajcfbg21rb4rb1cu3zartkut-4-0.jpg

Pride Mobility... | Answered on Apr 10, 2018


Hi remove the key & push freewheel lever into drive.,.. cheers

Pride Mobility... | Answered on Feb 02, 2018


Hoping your problem is in the wiring to and from , or the light itself , usualy when the board goes , nothing works... make sure you test every contact point for juice to and from , before you discard the possibility...!!!!
.

Pride Mobility... | Answered on Jan 06, 2018


get an electrician to make up a short extension lead attached to the handle bar

Pride Mobility... | Answered on Jan 05, 2018

Not finding what you are looking for?

Pride Mobility Products Topics

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Experts

Rob Hill
Rob Hill

Level 3 Expert

1367 Answers

Will

Level 1 Expert

25 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

Are you a Pride Mobility Products Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...