Possibly. What's the problem? Common problems include slow/no water flow or just hot/just cold water. This is often the automatic mixing valve failure or at least plugged screens.
GE Spacemaker is a generic range of appliances.
All questions in Fixya need full 'make model (what it is)', first 3 words.
If the stabilizers are broken Google for parts.
GE (numerical model number) Parts
https://www.google.com/search?q=GE+spacemaker+parts
Depending on age, they may no longer be available
..
I am sure I answered this yesterday?
You posted to washing machines category and this appears to be a gas fueled pool heater.
You would be best contacting a service engineer because it is gas powered, although if it does blow up, it is outside or will only blow up the pool house.
When the E4 error appears on your Aftron top-load washer, it usually means there's an issue with how the lid closes or locks. This error prevents the washer from knowing if the lid is shut tightly during use.
* Ensure the lid is completely closed and latched. If it's not fully closed, the washer will not start.
* Inspect the lid lock for any damage or blockages (e.g., dirt, debris, faulty latch) as these can prevent the lid from locking.
* Power off the washing machine and unplug it briefly, reconnect the power and restart the machine, this reset may resolve the error.
* Use a multimeter to check if the lid switch has continuity, this test will determine if the switch is functioning properly.
The L221 code on a Linde H20 forklift indicates a hydraulic fault, specifically related to the tilt pot.
L: This letter signifies a hydraulic issue.
221: Refers to a faulty tilt pot.
Here are some potential troubleshooting steps to address this issue:
Check the Tilt Pot Connection: Depending on the year of your forklift, the tilt pot's plug might have a poor connection. If it's an older model with a non-waterproof plug, moisture could be affecting it. Try unplugging it and cleaning it thoroughly with electric cleaner.
Inspect Wiring and Linkages: Verify that the wiring is intact and that the linkages are not worn. If everything seems fine, you may need to replace the tilt pot. Keep in mind that recalibration using a laptop might be necessary. Display Code L221 - Technical Troubleshooting discussion in Forkliftaction's forums
There are two wash cycle programs that default to a 30 degree wash for the Logik L814WM16. Set the machine program to Delicate or Eco to get a 30 degree C wash. Note: the Eco program has a maximum load of 2 Kg. The maximum load for the Delicate program is 2.5 Kg but may be lower when washing some fabrics.
There are also programs for Cottons at 20 degrees C and Express 15 degrees C. See page 17 of the manual, available here: https://manuall.co.uk/logik-l814wm16-washing-machine/ .
I hope this helps.
Cindy Wells
Question edited for clarity, 'make model (what is is)'.
GE spares suppliers. In most cases, these suspension rods are somewhat interchangeable. Most cities have a spares place where you can go and say "can I have one of these".
https://www.google.com/search?q=GE+TD1355PBAYN+parts
..
Errors TE, EC, TC mean that the temperature sensor that measures the temperature of the water in the unit is not working properly. Some codes - for example, TE - appear only before the start of the wash.
These codes are typical of both ordinary washers and those that have a drying function.
On a Washing Machine? A Top Loader?
Normally water being splashed where it shouldn't be. I would suspect the lid lock switch.
or
Water leaking to the motor, or motor controller board.
It depends if it is a top loader or a front loader. All question should have 'make model (what it is)' as the first 3 words.
A front loader is easier to fix.
vernel.pt
https://www.vernel.pt > Tips & Articles
From fabric softener not dispensing or not draining to a blocked washing machine's detergent drawer or one filled with water, we take a look at the most ...