Pride Logo

Pride Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 124 Products
  • 2K Answers
  • 154K Views

Either go to a pride dealer and get the proper job switch or look on eBay or Maplin for a similar. Check current rating of switch. Make sure you disconnect the batteries before attempting this job.

Pride Health &... | Answered on Jan 05, 2019


Do you mean a charger plugged in for four months ? or the battery pack on the scooter for four months ? if it not charging and left on the scooter they will discharge and may never recover.

Leaving it on charge for four months ?, the charger will go into trickle charge mode once it fully charged the batteries, manufacturers will agree this is a good thing , if left for weeks and weeks , it should be charged up fully once a week if not in use and i recommend removing the battery case as i seen issues arise from leaving a battery pack on a scooter for long periods of time, for starters they discharge quicker,.

Pride GoGo Elite... | Answered on Dec 26, 2018


I think I understand what you are describing based on some inadvertent button pushing on your part.
Sleep mode programming on the VSI controller by Penny and Giles Drive technology is the idle time of the power chair before it "goes to sleep". This computer menu is accessed using a hand held PP1 programmer that is plugged into the charging port of the joystick. Using this programmer one can scroll down to the sleep mode menu and set the time from I think 1 to 120 minutes ( I have not accessed this particular programming menu for quite some time).
If I put in 10 and save this number the chair will go into sleep mode after sitting and not being used for 10 minutes. The control may have dropped one of the settings due to a program glitch. I do not know of a way to reprogram this by pushing buttons on the control itself.
You should drive the chair into a local dealer who has a PP1 programmer and let them program it for you. This is a 2 minute deal and they should do this as a courtesy for you at no charge. If a technician comes out to your house they may charge you a minimum 1 hour labor charge.
While they have the programmer plugged in, have them check the fault log for any other problem areas. Hope this helps.

Pride New Jazzy... | Answered on Dec 11, 2018


No guarantees ... but you might first find the manufacturers plate on the scooter to get the model and serial number ... then call/contact Pride (go to pridemobility.com for contact options - see link below) to see if they can then tell you which year it was made. Pride Mobility Live Your Best Leader In Mobility Solutions

Pride Health &... | Answered on Nov 24, 2018


hi Peter at worse, ,sounds like a controller fault, are you uk based?
could be that the motor brushes are causing the fault.

If so i can repair them from £20.


regards
Rob

Pride Health &... | Answered on Nov 20, 2018


hi Kelly, please count the number of times it flashes then there be a pause and it will repeat. If the flashes are continuous never pause then that the controller telling you the batteries are getting low. Regards Rob

Pride Health &... | Answered on Nov 14, 2018


hi John, have the brushes been checked making sure they are not sticking inside the motor brush holder,

At worse it could be the wigwag pot, try moving the wigwag lever in the upwards or downwards direction as you go forward , be gentle to see whether that improves things, if it does , you require a new throttle pot.

Regards
Rob

Pride Health &... | Answered on Nov 14, 2018


hi, When you first start to go forward you should hear a clicking sound and once again when you stop, its the magnetic brake releasing, it stops you rolling on hills etc once you stop.

regards
Rob

Pride Health &... | Answered on Nov 06, 2018


fuse page 22
fault code 36
Just a thought, I know nothing about your cart but in cars when the battery voltage is getting low newer cars start cutting unnecessary voltage. You say your battery is charged but how good is it if the battery is charged but low could the lights be a computer way of saving voltage.
The manual link is below maybe it will help.
May be fuses, wiring or a connection.
manual
https://www.pridemobility.com/pdf/owners_manuals/intl_scooter/uk/uk_colt_xl8_om.pdf

Pride Health &... | Answered on Oct 24, 2018


just have a check of the fuse could be a blown one ?? hope this helps regards Jim

Pride Celebrity... | Answered on Oct 20, 2018

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Pride Experts

Rob Hill
Rob Hill

Level 3 Expert

1367 Answers

Marvin
Marvin

Level 3 Expert

84540 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pride Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...