Price Pfister Logo

Price Pfister Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 269 Products
  • 689 Answers

Replacement parts can be found on amazon. Click here Watkins Hand Soap Made Naturally Since 1868 and take a look. I hope this was helpful. Cheers

Price Pfister... | Answered on Feb 08, 2019

1 under the sink turn off both water supplies
2 disconnect the supply lines at the on/off valve EZer than at faucet
3 under sink unscrew the retaining nut(s)
4 on top wiggle or pry the faucet and lift up and remove.
5 know you can replace the spout and don't forget the new O ring that's why it leaks anyway. you really just need the new washer O ring .
6 Reinstall check for leaks
7 caulk around faucet.

Hope this helps Mike

Price Pfister... | Answered on May 31, 2018


Here is what I would suspect at this point:

- Incorrect air pressure in tank, or

- Clogged filters

To check air pressure:

Empty tank and check pressure -- it should be 7 PSI.

Note: There is a rubber bladder in the tank in which the water is stored -- if this bladder is ruptured, the air pressure in the tank will not hold.

So, adjust air pressure, try system again. If it works for a while and then stops, empty tank and check air pressure for 7 PSI.

Clogged filters?

If the system doesn't work when tank pressure is adjusted, empty tank and check pressure again. If pressure is still 7 PSI, then replace filters.

If tank pressure is not 7 PSI at this juncture, it's probably a ruptured bladder and the tank will have to be replaced. But before you take that tack we should "talk" again.

Please let me know the results...




P.S. I'm assuming you have adequate water pressure on your household system. You're not noticing a drop in pressure anywhere else in the house -- is that correct?

Price Pfister... | Answered on May 08, 2018

I had the same problem. The Price Pfister web site recommends removing the handle (unscrew the dome cap, then remove the phillips screw to get the handle off) then tightening the retaining ring (I used channel lock pliers on largest setting. It worked. However the retaining ring is plastic on some models, and they recommend replacing it with a brass one. I haven't taken that step yet, we'll see how it goes (mine is plastic).

Price Pfister... | Answered on Feb 25, 2018

If you just installed it check to see if it has a water saving feature that in some homes and almost restrict all the water force

Price Pfister... | Answered on Feb 18, 2018

Back to the basics...did you turn the hot water shutoff back on? Is it a multi-turn shutoff or a 1/4-turn one? If it was old, and multi-turn, the washer could be shot, and it is all clogged. Try disconnecting the hose and see if you can get any flow into a bucket from the connection.

There could be some crud caught inside of the cartridge, so you might need to remove it and flush it out. Price Pfister single handle sink faucet no hot water

Price Pfister... | Answered on Feb 12, 2018

There should be a nut hatched to faucet. If not there look in cabinet.

Price Pfister... | Answered on Jan 13, 2018

No be sure water is off. Take this apart with still being supplied will cause you a lot of trouble, wife will be very unhappy.

Price Pfister... | Answered on Dec 30, 2017

The valve body was installed too close to the front of the wall. Open up the wall and set it back per the instructions or live with it.

Price Pfister... | Answered on Dec 30, 2017

Google your faucet and add how to fix leak there is a video on there site that shows you how to do it .

Price Pfister... | Answered on Dec 09, 2017

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Price Pfister Experts


Level 3 Expert

4356 Answers

Donni Steen

Level 3 Expert

687 Answers

ray gallant

Level 3 Expert

60412 Answers

Are you a Price Pfister Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides