Precor Recent Questions, Troubleshooting Help & Support

http://www.precor.com/products/media/english/Treadmill_932i_Manual_Maintenance_Reference_Assembly_English.pdf

Service Manual, 9.31, 9.33, 9.35.fm (sportsmith.net) PRECOR 9.33 OWNER'S MANUAL Pdf Download ' ManualsLib Precor LOW-IMPACT TREADMILLS 9.33 User Manual ' 86 pages ' Also for: LOW-IMPACT TREADMILLS 9.31 (manualsdir.com)

You will need to replace the battery

A sticky button is the most likely cause https://www.google.com/search?q=Model+956i+won%27t+speed+up ..

No idea, try google.

We are FIXYA dot com. We are not Precor and we certainly don't take credit card numbers. By 'charging bat', you mean battery for the display. The battery is mentioned 67 times in the manual. Press CTRL+F and type in 'battery'. Page 39 and 40, looks to be what you need. https://primofitnessusa.com/wp-content/uploads/2017/01/V3-precorefx-546i-V3-elliptical.pdf Links to Precor if you need to buy something?

EFX 546i Elliptical Fitness Crosstrainer - Precor (CA)

www.precor.com > en-ca > efx®-546i-elliptical-fitness-...

Durable 6-phase generator system has no contacting parts, reducing friction and wear, and provides 20 levels to tailor workouts with consistent resistance. The 20 ...

Precor EFX 546i Commercial Series Elliptical Fitness ...

www.amazon.ca > Precor-Commercial-Elliptical-Fitness...

The Precor EFT 546i elliptical has an adjustable cross ramp that allows users to select an angle between fifteen and forty degrees. This allows for isolation of the ... ..

Verify voltage to the MCB. If it gets power, and 2 MCBs do not light up the console, check the wiring to the console. If that looks good then it sounds like you need an upper. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/russell_1d1c35fa8a5a0be4

Go to National Gym Supply @ gymparts.com or call them @ 1-800-496-7278

Look on the back for a reset button, it could be a small red button the size of pencil lead protruding slightly, push in on it. It could also be located in side a small hole the same size use a tooth pick or something none metallic to push with...

Here's a link that will take you to the page for a few 5.23 models. You'll want to narrow the search on the left column by serial number to get to the correct information on your exact model. Repair Parts for Precor 5 23 Ellipticals Consumer SPORTSMITH net Here's a link to a few fuses that are listed for the 5.23's: To determine which one is correct, you'll need have your serial number off the machine: Repair Parts for Precor 5 23 Ellipticals Consumer SPORTSMITH net

This link will allow you to use your model and serial number to find the correct battery along with the service manual with replacement instructions. Repair Parts for Precor EFX 546i Ellipticals SPORTSMITH net

GOLD99BET

disassemble as much as you can, and dry up all parts. hope that the electrical circuits/parts weren't damaged.

You probably have a circut board malfunction.

It might be the battery. A fully charged battery is required to move the ramp up and down. The battery is like a car battery, if you don't use it then it dies and might need to be replaced.

To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted. https://www.sportsrec.com/reset-error-code-precor-treadmill-5519820.html https://www.youtube.com/watch?v=_yD5eoMNB64

https://www.precor.com/en/efx®-546i-elliptical-fitness-crosstrainer™ use of: https://www.youtube.com/watch?v=YRFJNFIHAHY

https://www.youtube.com/watch?v=M3u-jvWGTs8

Hi There....This is a great message for ALL PRECOR 956/966 owners. This failure usually relates to a "communications" error between the upper and lower electronics. This particular failure is a direct result of a failed IFT drive module, or the lower drive "box" that is made by Advanced Drive Technology. The brains of this lower controller has failed and cannot "talk" to the upper board anymore due to several failed parts inside this box. You are lucky to have this failure arise over a fatal blow-out. Now replacements thru Precor or a distributor will be $550+ and are usually low stock items at places, but you can get repairs and exchanges of this Precor IFT drive by emailing gregATbuyfitnessrepairpartsDOTcom for much less than all other vendors. Currently these IFT drives are 380 exchange and 199 repair and turnaround is one day. Good Luck!

Is it on an extension cord? Take it off any extension cords and make sure it's on a dedicated 120v circuit. No other items on the circuit. Also, how old is it? Precor made a bunch of the 9.3x series from 2002-2005 with an aluminum tail roller that can cause problems. Check the back roller. Is is silver and non-magnetic? if that's the case, you have an aluminum roller and you need to contact precor. If you're the original owner of the machine, they should warranty the replacement of the parts, if not, you'll have to buy at the very least a running belt and new roller.