Pramac Logo

Pramac Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 100 Products
  • 167 Answers
  • 27K Views

I don't know your equipment, but the unbalanced term may refer to too large a load connected to one leg of your split phase service. Go to your load panels and try to get the amps drawn by your loads to be more equal. You may be over taxing one leg and have available capacity on the other, assuming you are running a 110/220 V split phase output.

Pramac... | Answered on Mar 15, 2019 | 33 views


website reliablestore it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

Pramac... | Answered on Feb 08, 2019 | 43 views


portable generator head stoped making power engine runs fine sircut brakers are fine

Pramac... | Answered on Jan 29, 2019 | 825 views


Water level, good thermostat, good water pump, fan working? All things to check.

Sometimes an airlock will prevent water circulation

ALSO verify your temp gauge and sensor is working correctely. A failure of these may appear as high temp and even shut machine down if the sensor is bad.

Pramac GBW30P... | Answered on Jan 22, 2019 | 294 views


The leakage fault of diesel generator is usually caused by the injection of corrosive coolant or seawater into the water radiator of the diesel engine.

Cause of failure: 1. The cooling water added to the cooling water radiator by operator is seawater, which results in the damage of internal waterway and external interface of diesel engine. Therefore, the use of diesel engines must be strictly in accordance with the provisions of the diesel engine operation. 2, the operator feed water radiator in the addition of strong anti-freeze corrosion, resulting in diesel engine waterway parts damage. Troubleshooting methods:
1.Disassemble damaged parts of diesel engine, replace damaged parts of diesel engine after washing water radiator and inner waterway of block with fresh water.
2, after assembly, adjustment, test machine found that the diesel engine returned to normal, the fault was eliminated.

Pramac GBW30P... | Answered on Jan 22, 2019 | 111 views


my 500 kva diesel generetors dosnt work since mornning its workes after 4 houres when the weather changed

Pramac GBW30P... | Answered on Dec 22, 2018 | 372 views


1: Check if the alarm is stopped, a, low oil pressure b, high water temperature c, overspeed, etc.;

2: Check if it is overloaded, whether the inlet and outlet pipes are unblocked

3: Check if the parts are broken or loose, and check if the fuel tank is short of oil.

4: Check if the fuel injection pump is damaged

5: Check the speed sensor, electronic speed control board, actuator, etc.

Pramac GBW30P... | Answered on Dec 22, 2018 | 264 views


You run again the generator but before running, check & mark the oil level. Then stop the generator & wait until the oil settle to the bottom of oil pan. Check the oil level again & if the oil level is higher than the marking before that's means you have an engine gasket leak.You need to replace that gasket.

Pramac GBW30P... | Answered on Dec 18, 2018 | 656 views


what safety caused the alarm. if you cant restart it, it may be cause the problem that originally shut the engine down has not been fixed, it could be water level, low oil, high water temp, low fuel,over voltage, all of the above are probably run through the safeties. over volt, and water temp would probably clear its self after it sat a while. try turning off power to panel. for a couple minutes and see if it will reset, if not check water level. and oil levels

Pramac GBW30P... | Answered on Dec 18, 2018 | 256 views


by finding the problem --check oil and circuits

Pramac... | Answered on Dec 11, 2018 | 49 views


Did you have a auto controller?
With the switch set to AUTO, the engine may crank and start at any time without warning. Such automatic starting occurs when utility power source voltage drops below a preset pevent or during the normal exercise cycle. To prevent possible injury that might be caused by such sudden starts, always set the switch to OFF and remove the fuse before work. Ing on or around the generator or transfer switch.

Pramac GBW30P... | Answered on Dec 07, 2018 | 156 views


The distance between the sensor and the diesel generator flywheel is too far or too close (generally this distance is approximately 2.5 + 0.3 mm). If the distance is too far, it may not be able to sense the signal. If it is too close, it may damage the working surface of the sensor. Due to the high-speed operation of the flywheel, radial (or axial) turbulence occurs. The distance is too close to pose a great threat to the safety of the sensor. It has been found that several working faces of the probe have been scratched. According to practical experience, the distance is generally about 2mm, which can be measured with a feeler gauge.

Pramac GBW30P... | Answered on Nov 21, 2018 | 117 views


If the unit has a battery box, measure it and get the largest size that will fit and of course the correct voltage. Diesels take a lot to crank.

You can search battery sizes on the internet for physical size. NAPA has a pretty good selection.

Pramac GBW30P... | Answered on Sep 27, 2018 | 599 views


The controller circuit card needs to be replace. This is
the one that senses if and when power is shut off. This
will automatically start the engines.

Pramac GBW30P... | Answered on Sep 27, 2018 | 223 views


Ensure any engine control switch is set to the run position, with the load disengaged. Manually set the air shut off valve (if fitted) to the run position (see Fig. 18), Turn the key switch to the start position, which will energize the solenoid allowing the engine to crank over for a few seconds then start.

Check the instrument panel is showing normal running oil pressure, and the ammeter for charge to the engine batteries.
Allow the engine to run for five minutes checking the instruments are reading correctly. Stop the engine and check the oil and coolant levels, replenish if necessary.


https://www.dieselgeneratortech.com/generator-sets/normal-starting-procedure-of-Perkins-generator-set.html

Pramac GBW30P... | Answered on Aug 21, 2018 | 163 views


Hello. Maybe you have solved your problems. But I still want to share the helpful article to you. https://www.dieselgeneratortech.com/diesel-generators/why-diesel-generator-fail-to-start.html

We are Perkins diesel generator OEM. Can provide 22KW to 2200KW diesel generator set with Perkins engine. https://www.dieselgeneratortech.com/perkins

perkins diesel generators-n5v1fnwbur1qlbncsxenjidv-1-0.jpg

Pramac GBW30P... | Answered on Aug 09, 2018 | 467 views


check for dirty or corroded connections or loos weir's

Pramac GBW30P... | Answered on Aug 07, 2018 | 316 views


Try Googling (Pramac)(P6000s)(manual) without parens.

Pramac... | Answered on Mar 22, 2018 | 262 views


Check for floating debris in fuel tank possibly restricting fuel flow thru screen on bottom of fuel pickup;

Pramac... | Answered on Mar 07, 2018 | 274 views


Check fuse. If there is an indicator, instrument or light, on the output, check what it says. Loose contact is a possibility.

Pramac Powermate... | Answered on Oct 24, 2017 | 214 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Pramac Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Lawrence Oravetz

Level 3 Expert

10528 Answers

wadingriver
wadingriver

Level 3 Expert

2222 Answers

Are you a Pramac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...