Pramac Electrical Supplies - Page 9 - Recent Questions, Troubleshooting & Support

there is a screen in the tank at the shutoff valve best bet it to remove it and tear it out and use a in line filter where it is easier to replace

Start looking at your safety circuits.

1. High water temp
2. Low Oil
3. Low water etc...

From the manual these are the protection circuits.

• Engine protection: low oil pressure, high engine temperature.
• Genset protection: under/over voltage, overload, battery charger failure, battery voltage out of limits,
under/over frequency, start failure.
• Circuit breaker protection: IV poles.
• Differential protection.


Any one of them will trip the fuel relay closed. What you may be able to do is disconnect one at a time each protection circuit and see when the fuel relay opens. (Make sure to reconnect each one if it had no effect on the fuel solenoid)

Once you isolate which circuit it is in then you can chase wires or change the bad switch.

Thanks for choosing FixYa.

Kelly

This may sound over simplified but..... old battery cables corrode onboth ends so you have less amperage carried by the cables. (i.e. fewer strands of copper trying to carry more amperage than they are capable of. The next time you do a start cycle place your hands on the battery terminals one at a time and check to see if they are HOT to the touch. Also do the same thing for the chassis ground and the terminal lug at the starter. ANY hot terminal is a sign the cable has broke down either from age/vibration wear or corrosion. If you suspect the battery cables are bad get a VERY GOOD set of jumper cables (2 sets connected together if necessary) and do a direct from the battery to the starter connection. This is loads of amperage so be very careful and DO NOT do this alone. But, if the starter spins faster you have battery cable problems.

IF you have an external to the starter relay that too can cause the problem due to worn / defective contacts.

I will watch for any responses.

Thanks for using FixYa.

Kelly

Try to check (move up and down) the level sensor if it is really in the external tank. The flowing bowl may be flooded.

This likely has a diode module which rectifies a low voltage AC winding to do the charging.

Things to check: There USUALLY is a fuse on the low voltage winding. It SOMETIMES is within the generator covering.

Check for loose connections or broken wires.

The diode module is usually a 25 amp block about 1.25 inches square with 4 faston terminal connections.

Use a meter set to AC to check voltage on the AC terminals... might be around 18 volts or so.

Then on the DC terminals labeled + and - with meter set to DC.

To charge a 12 volt battery there needs to be about 13.75 volts or so.

there are just a few thing's that cause this, one is the voltage regulator is failing and the other is one phase of the three phase Alternator is open, u will need to have the alternator windings tested for continuity and shorts to ground, also a unregualted voltage test to determione if the voltage regulator is the problem.

Refer to the NEC (National Electric Code) for ampacity rating of cables.

These depend on the wire size and insulation and the type of cable.

When in doubt or near a limit, go one size or two larger. When cable is long, go a couple sizes larger (smaller number).

There are two 14mm bolts on both sides (lower) of the motor. Unscrew one or both and drain the oil....Replace with sae 30 or 10w30 oil and should take almost a quart. (Put the bolts back in and tork slightly.) Check oil level.

Adjust engine speed

you should have a drain plug at the side and bottom of the motor crank case its a small plug with a square head how old is your generator if new put 10w30 oil if old put sae30w if really bad add some lucas oil treatment also now a 9 h.p. should take less then 2 quarts

Yes

No one gives sizing. https://generatorguru.com/spark-plug-27901063/ https://www.google.com/search?q=united+power+generator+Model+GG2900+parts ..

https://cleanestor.com/how-to-clean-up-freon/?expand_article=1 This should help

No connecting to your utilty company in South Africa. Just FYI, we are a North American site and my not always have the answer, in this case we do Https://www.facebook.com/ConlogSolutions/posts/im-having-a-rf-con-error-cant-do-anything-on-the-gadget-please-help-on-how-to-re/962048393965724/ Quoting from link above: "Conlog Hi Ola-daniels, Please see below steps to assist with RFCON error : * Press the Back arrow on the keypad - this step is to refresh the UIU ( the device) * Type # 75 # - this is to check the signal strength If it does not go back to the normal display *Type # 80 # - this is to refresh the meter Then lastly you can repair the meter and the UIU by # 36 # The above steps will work better if you are outside the house because the meters uses the radio frequency connection The above error will occur in instances of bad weather conditions or if there is load shedding or power failure If the problem persists after trying the above you may contact the municipality or the service provider."

SOLVED: How do I clear up the rf con error on my meter ...

https://www.fixya.com > ... > The

May 7, 2020 - How do I clear up the rf con error on my meter because I want to ... Https://www.facebook.com/ConlogSolutions/posts/im-having-a-rf-con-error- ... Hi Ola-daniels, Please see below steps to assist with RFCON error : ... shut down the energy alimentation for 2 minute ,but if the defect persist error it show again. SOLVED: Pole meter conlog rf con meter keep on freezing ... Jan. 10, 2017 Meter reading shows rF CON instead of units available - Fixya Jun. 24, 2018 SOLVED: Good day my conlog ip54 elecricity meter showd ... Oct. 6, 2018 SOLVED: Rf con error - Fixya Jun. 20, 2020 More results from www.fixya.com

Please Help With My Conlog Prepaid Meter - Technology ...

https://www.nairaland.com > please-conlog-prepaid-meter

Aug. 6, 2020 - ystar: If the conlog meter is showing rf-Con, it means power supply doesn't reach the meter at all its either Loss of phase from the transformer or a loose contact ... How Do I Load The Activation Token On My Conlog Prepaid ... Mar. 17, 2020 I Need A Technician To Fix This... - Nairaland / General - Nigeria Jul. 22, 2019 I Need Number Codes To Reset Memmcol Prepaid Meter ... Jan. 11, 2019 More results from www.nairaland.com

Consult a qualified electrician.

Your instruction manual should have that information. https://www.manualslib.com/