Power Acoustik Popular Questions, Answers, Tips & Manuals

heat ur solder up an remove the power from where it is

Here, use the following link. It will take you to the troubleshooting on page 36. I hope this helps, let me know if you still have any problems.
http://www.poweracoustik.com/pa2006/manual%20and%20catalog/ceiling%20mount%20monitors/PMD-112CMX.pdf

your pink wire is not conected to ground

• You double the watts to the speaker for the channels bridged. This also depends on the Ohms of the speakers being used. The lower the Ohms of the speakers used in relation to the Ohms of the amp also increases the watt output of the amp.

Regards, Tony

Sounds like you need to run a heavier Gauge wire for power source. If power source wire is too small, you will get a voltage drop. Check your source wire gauge compared to connector on equalizer. You may end up having to run a heavier gauge direct to battery, with fuse link in line. See what the amp requirements are in manual, and make sure wire is heavier than minimal. Example: if 15 amp required, I'd go to 12 gauge minimum, or to be safe 10 gauge. (longer the run, heavier the wire.) Be sure all connections are good as well.

It only supports MP4 format, so that is what you need to convert the videos to. Here are the specs: http://www.shopping.com/Power-Acoustik-PTID-4003TV/info

it sounds like you have a shorted wire or a blown speaker in system

try disconnecting all speakers and see if light goes out if so it is bad speaker if not try disconnecting all speaker wires and see if light goes out then

also if disconnecting speakers fixes problem you might want to check what the Ohm load is and how you have multiple speakers hooked up if Ohm load is too high or low you will get same light

is it possible you have too much moisture in car - sometimnes that will cause error

if this does not help please contact me with as many details as you can give me and i can try to help more - number of speakers, how they are wired to amp, what amp, how many channels for amp, etc - the more info the better i can help

good luck!

you can get parts from digikey.com.

look at the transistor you want to replace, they all have part numbers on em.

type it into the search frame on the site.

Sounds like going over the tracks might have knocked a wire lose behind the dash. The only way to know would be to take out your head unit to reveal what's behind it. Make sure all the cables are securely fastened and it should work again.

Hello,

how long have you been using this player? I suspect the laser (lens) of the player. I think the laser (lens) is weak that's why it cannot read data/files on DVD discs.

To confirm if actually its a laser problem, insert an Audio CD into the player and see if will play. If it plays, then obviously, your laser (lens) is weak. But if it doesn't play Audio CD, then it might still be the laser (lens) or a mechanism problem.

Get a lens cleaner, use it to clean the lens. If that doesn't solve the problem, get a screw driver, open the player's cover so that you can gain access to the lens, use a cotton board to clean the surface of the lens. This should clean dust or dirt that might be on the lens.

If non of the above solves the problem, then know that you need to replace the laser to a brand new one.

To replace the lens, remove the bad laser, use it as a sample to get exactly the same type and do the replacement. Note that replacing a laser (lens) needs a professional touch, so if you cannot replace the laser, get it to a repairman to fix it for you.

Once this us done, your player will play all DVD discs again.

Good luck.

try to go on ebay.com and look at the price of one u need to sign up tho for ebay.

What regulators are you talking about?

Wire as per the diagram:

i think it will read anywhere Between 12 and 14 Farad.. not Positive but hope this helps ;-)

hi at the rear of the amp where the power terminals are open it and where the power terminals conect to the circuit board you will see a black diode this is what we call a dummy or a reversed diode you will have to remove this and replace it if you dont and this happens again there will be more serious damage done and may be unrepairable let me know how you get on

go to the video setting on the menu select the color system compatible with monitor you installed.there are different color system in a monitor they called pal,pal secam, me secam ntsc etc.select the proper video setting...good luck let me know how it goes...

Hi There and Welcome to FixYa,

In many amplifiers, this condition that you have can mean that it has either a power supply failure or a blown fuse. The cause of this can most of the time attributed to sudden drop in voltage.

With this, I am strongly recommending that you have this amp checked by a technician to determine if you have :

• Melted fuse
• Or if the fuse holders are still usable

Generally, when the fuse holder melts, the contacts become badly oxidized and the clips lose their tempering - this means that it will continue to overheat and will not function properly, hence, the problem that you're having right now.

I certainly hope this helps,

Thank you for using FixYa.

usually not a code. it is unlawful to drive without the parking brake feature hooked up.... but the way to do it is remove the wire from the parking brake and ground it. it will then think the parking brake is on

Hello... sorry to hear you are having problems! First we need to determine if you have a factory aftermarket navigation system If it is factory, there is not very many options for you the consumer to do yourself. If you have an aftermarket radio (store bought) then find where the antenna is located. Most of the newer antennas are about 1 inch by 1 inch square. If it is on your dashboard, it needs to be routed to the exterior of the vehicle. Navigation is done by "line of sight" with the satellite. If it is blocked by metal under the dash or the under the roof of the vehicle then that would be your problem. If your antenna is outside the car, then you may have a break in the line which would require replacement of the antenna. All that I have spoke of is if you have an aftermarket system. Each aftermarket system is gender specific, meaning if you have a JVC headunit, then you will have to go to a shop that carrys or can get JVC parts. Maybe this helped! Good luck with your venture!

20 year car audio/video installer
Bay Manager

That is going to be hard to find anywhere but from the manufacturer. I would give them a call or email @ Website:http://www.poweracoustik.com

Street address:5920 E.Slauson Ave

Commerce, CA 90040

Phone:323-722-3333