Hi,
Please check that the mute button on the device or any associated remote control is not stuck in the down/pressed position. If not, then please switch the sound source and test the device for sound again. Otherwise, we can move onto a power cycle of the device.
Thank you.
There could be a few reasons why you are not getting any sound from your vintage VSX 5600 Pioneer home theater system. Here are some things you can try:
Check the connections: Make sure all of the cables are securely connected to the appropriate ports.
Check the power: Make sure the home theater system is turned on and the power cord is plugged in.
Check the volume: Make sure the volume on the home theater system and the volume on your TV are turned up.
Check the input: Make sure the home theater system is set to the correct input.
Check the speakers: Make sure the speakers are turned on and properly connected.
There might be a connection that could be loose here to have your TV be turning off or there is a problem with the TV's power supply or a Tcon board problem or the power cord might be bad.
There may be a problem with the stereo itself, or with the power supply. If the stereo is plugged into an outlet, try plugging it into a different outlet to see if that makes a difference. If the problem persists, you may need to consult a stereo repair specialist.
Hi there! It sounds like you're having some issues with your Pioneer stereo.
For the first issue, it could be due to a faulty connection or a software issue. To troubleshoot, first check all the connections between the head unit and the speakers to make sure they are securely connected. If the connections are secure, then check the wiring connections to make sure they are not loose or frayed. If the wiring connections are good, then the problem could be with the head unit itself and you may need to contact a professional for further assistance.
For the second issue, it could be due to a faulty connection, a wiring issue, or a software issue. To troubleshoot, first check the speaker wires to make sure they are connected properly and not loose or frayed. If the wires are secure, then you should check the setting on your amplifier or stereo to make sure the rear speakers are enabled. If the rear speakers are enabled, then the problem may be with the wiring or with the head unit itself and you may need to contact a professional for further assistance.
Hi,
please call the manufacturer and ask them to email you the manual or check with a seller of the product on the amazon or ebay websites and ask for the manual. They should be able to create a product listing for you to acquire it.
Thank you.
Old technology and new technology often don't mix. Your television is new and geared up for Bluetooth and HDMI, your old surround sound system is composite video and audio. You need to test the television with something else, and then check the surround sound with a different input. If they both work then you know it is a compatibility issue. Your best bet is a new Bluetooth Sound Bar that is as good as the television.A similar issue was posted here yesterday, so you are not alone.https://www.fixya.com/support/t29896811-jvc_rx_6018v_not_working_tv..
HI, I’m Stephen. This works!!!! This saved me $200.00 I am eternally thankful! the key to it is pressing the little reset button. it is very small and only accessable with a pen. If you follow the directions as listed, it will work.
OR
Hi, You set the screen so its all the way down and hold down the dvd eject then the reset button for a few seconds, then let off of the reset button, keep the eject button held down for another few seconds. Then the screen will say press reset. instead using the joystick, press up,up,down,down then push it in at the center. It will come up with options. the first one is touch screen test. using the joystick click on that one and do the calibration test. You will then have to trace the outline of the screen, while you are on the right side of it, trace it short to make up for the buttons on the right side. when you finish push the joystick in. it will say "settings ok" then go down to the 4th one, i think, and it will say something like test calibration settings and go to that one. It should say that the settings were saved. After that shut the key off and turn it back on and it should be good to go.
Question edited for clarity and better English.
You don't say what language you want to change to? I get the impression that English is not your your first language.
Here is the manual
https://toyota.jp/manual/navi/nscp-w62.pdf
It is only in Japanese. The Toyota Aqua is a Japanese Home Market Model, so the stereo is probably only in Japanese unless you can get a firmware update to where you live.
Toyota Aqua (Japanese: ???????, Hepburn: Toyota Akua) is a full hybrid electric subcompact/superminihatchback (B-segment) manufactured and marketed by Toyota since 2011. The nameplate is exclusive to the Japanese domestic market,
It is also the Toyota Prius in other countries, so the videos might help. There is also a trick to use a smartphone with the Google Translate app on it and use the camera feature to translate what you see onscreen. Look for Settings - Language.
Hi,
Please press the Home button, wigdget/circular symbols, tools symbol > then systems >camera settings > back camera input > On
You can also reference your manual for these steps as well.
Thank you.
Your pioneer receiver should pickup radio signals. Set the receiver to fm and make sure volume is up and mute is not on. Installing an antenna will bring in more stations.