Pioneer AVH- p 2300 wire pinout for power plug
Here is the wire pinout for the power plug of the Pioneer AVH-P2300 car stereo:
- Yellow: Constant 12V (Battery)
- Red: Ignition 12V (Accessory)
- Black: Ground
- Blue: Power Antenna Control
- White: Front Left Speaker (+)
- White/Black: Front Left Speaker (-)
- Gray: Front Right Speaker (+)
- Gray/Black: Front Right Speaker (-)
- Green: Rear Left Speaker (+)
- Green/Black: Rear Left Speaker (-)
- Purple: Rear Right Speaker (+)
- Purple/Black: Rear Right Speaker (-)
6/24/2023 7:55:22 PM •
Pioneer...
•
55 views • 1 helpful votes
Pioneer vsx1020 wont turn on with telly,if I unplug 15 min from power point does but when turn off telly turn off amp which is good,but if I turn on once again the telly,amp wont turn on
If your Pioneer VSX-1020 receiver is not turning on along with your television, here are a few troubleshooting steps you can try:
- Check the power connections: Ensure that the receiver is properly plugged into a power outlet and that the power cable is securely connected to the back of the unit. Also, check if the power outlet is functioning properly by plugging in another device.
- Reset the receiver: Perform a soft reset by turning off the receiver, unplugging it from the power source, and waiting for about 15 minutes. Then, plug it back in and turn it on. This can help reset any temporary glitches or issues with the receiver's electronics.
- Check the remote control settings: Verify that the remote control is properly set up to control both the television and the receiver. Make sure you have followed the instructions in the receiver's manual for programming the remote control to work with your specific television brand.
- Test with a different HDMI cable: If you are using an HDMI connection between the receiver and the television, try using a different HDMI cable to rule out any potential cable issues. Sometimes, a faulty cable can prevent the devices from properly communicating.
- Update the firmware: Visit the Pioneer website and check if there are any firmware updates available for your receiver model. Updating the firmware can sometimes resolve compatibility issues and improve overall performance.
- Contact customer support: If the issue persists, it may be best to contact Pioneer's customer support for further assistance. They can provide specific troubleshooting steps or advise on whether the receiver may require servicing or repair.
Remember to consult the receiver's manual for additional troubleshooting steps and to ensure you are following the correct procedures for your specific model.
6/17/2023 5:38:44 AM •
Pioneer...
•
43 views • 1 helpful votes
I need a manual for Pioneer MOSFET 60w x 4
You can find the manual for the Pioneer MOSFET 60w x 4 car stereo on the Pioneer website. Here are the steps to find and download the manual:
- Go to the Pioneer website (www.pioneer.com)
- Click on "Support" in the top menu.
- Select "Car Entertainment" from the drop-down menu.
- Click on "Car Stereo" under "Product Category."
- Scroll down and find the model number of your Pioneer MOSFET 60w x 4 car stereo.
- Click on the model number to go to the product page.
- Click on the "Manuals and Downloads" tab.
- Select the manual you want to download and click the "Download" button.
Alternatively, you can try searching for the manual on the internet by typing "Pioneer MOSFET 60w x 4 manual" into a search engine.
Pioneer DVL 919 LD player standby light blinking.
Un voyant de veille clignotant sur un lecteur Pioneer DVL-919 LD peut indiquer un certain nombre de probl?mes. Voici quelques causes et solutions potentielles :
- Probl?me d'alimentation : V?rifiez le c?ble d'alimentation et assurez-vous qu'il est correctement branch?. Si c'est le cas, essayez de brancher le lecteur sur une autre prise. Si le voyant de veille continue de clignoter, il se peut qu'il y ait un probl?me avec l'alimentation. Dans ce cas, le lecteur peut avoir besoin d'?tre r?par? par un technicien professionnel.
- Probl?me de plateau de disque : Si le plateau de disque n'est pas correctement ferm?, le lecteur ne s'allumera pas. Assurez-vous que le bac est compl?tement ferm? et verrouill?.
- Probl?me de chargement de disque : Si un disque charg? dans le lecteur cause un probl?me, le lecteur peut ne pas s'allumer. Essayez d'?jecter tous les disques qui se trouvent dans le lecteur et voyez si le voyant de veille cesse de clignoter.
- Probl?me de micrologiciel : dans certains cas, un probl?me de micrologiciel peut ?tre ? l'origine du clignotement du voyant de veille. Essayez de r?initialiser le lecteur ? ses param?tres par d?faut. Pour ce faire, d?branchez le lecteur de la source d'alimentation, attendez quelques minutes, puis rebranchez-le.
Si aucune de ces solutions ne fonctionne, il peut y avoir un probl?me plus grave avec le lecteur qui n?cessite un entretien professionnel.
3/12/2023 6:39:08 PM •
Pioneer...
•
85 views • 0 helpful votes
Fl off blinking Red PIONEER VSX-S520
To perform a reset on your Pioneer VSX-S520 using the remote controller, follow these steps:
- Make sure the receiver is turned off.
- Press and hold the "BAND" button and the "STANDBY/ON" button simultaneously until the display starts flashing.
- Release the buttons and the display should stop flashing.
- The receiver is now reset to its default settings.
If the "Fl off" blinking red light persists, it could indicate a problem with the receiver that requires further troubleshooting or repair.
How can I download the English version for Pioneer Carrozzeria MRZ99 please?
Japanese only on this model.
How do I change the language on my Pioneer carrozzeria?
Question : I have a carrozzeria AVIC-****. Can I switch the language to English ?
Answer : Carrozzeria AVIC-**** is car navigation & AV model designed and sold for Japanese market only. The language cannot be changed to English, French or any other languages, and the instruction manual is in Japanese only.
..
How to wire up PIONEER GM 2000
The Pioneer GM-2000 is a two-channel amplifier that is designed to boost the sound output of your car's audio system. Here are the steps to wire up the Pioneer GM-2000:
- Disconnect the negative terminal of your car battery to prevent any electrical short-circuit.
- Locate a suitable location to mount the amplifier in your vehicle. Ensure that the amplifier is mounted securely and won't interfere with any moving parts in your car.
- Run the power cable from the battery to the amplifier location. The power cable should be of sufficient gauge to handle the current draw of the amplifier. Consult the amplifier manual for the recommended gauge of wire.
- Connect the power cable to the positive terminal of the amplifier and secure it in place.
- Connect the ground wire to a metal surface near the amplifier location. Ensure that the surface is clean and free of rust or paint, and that the wire is securely attached.
- Connect the remote wire to the amplifier's remote input. This wire provides a signal to turn the amplifier on and off when the head unit is turned on and off.
- Connect the speaker wires to the amplifier's speaker output terminals. Ensure that the positive and negative wires are connected to the correct terminals.
- Connect the RCA cables from the head unit to the amplifier's RCA input jacks. These cables transmit the audio signal from the head unit to the amplifier.
- Turn the amplifier on and test the audio output from your speakers. Adjust the gain and other settings as necessary to achieve the desired sound quality.
Remember to consult the amplifier manual for the recommended wiring instructions and to ensure that you follow proper safety precautions when handling electrical components. If you are not confident in your abilities, it is recommended to seek professional installation.
How do I reset my pioneer VSX-D711
To reset your Pioneer VSX-D711 receiver, you can follow these steps:
- Power off the receiver.
- Press and hold the "Advanced Surround" button on the front panel of the receiver.
- While still holding the "Advanced Surround" button, press and hold the "Standby/On" button.
- Continue holding both buttons for a few seconds until the display on the front panel of the receiver shows "Resetting."
- Release both buttons.
The receiver will now be reset to its default settings. Note that this will erase any custom settings or presets that you may have programmed into the receiver.
If the above steps do not work, you can also try the following:
- Power off the receiver.
- Press and hold the "Tuner" and "Band" buttons on the front panel of the receiver.
- While still holding both buttons, press the "Standby/On" button.
- Continue holding all three buttons for a few seconds until the display on the front panel of the receiver shows "Reset."
- Release all three buttons.
Again, this will reset the receiver to its default settings and erase any custom settings or presets that you may have programmed
My pioneer sw-8 subwoofer will not power on
If your Pioneer SW-8 subwoofer is not powering on, there are a few things you can try to troubleshoot the issue:
- Check the power cord: Make sure that the power cord is securely plugged into both the subwoofer and a working electrical outlet. If the power cord is loose, try unplugging it and plugging it back in.
- Check the power switch: Make sure that the power switch on the back of the subwoofer is turned on.
- Check the circuit breaker: The subwoofer may have a circuit breaker that has tripped. Check the circuit breaker on the back of the subwoofer to see if it has tripped. If it has, reset it by pushing the button back in.
- Check the fuse: The subwoofer may have a blown fuse. Check the fuse on the back of the subwoofer to see if it has blown. If it has, replace it with a fuse of the same rating.
- Check the auto power function: The subwoofer may have an auto power function that turns it off after a certain amount of time if there is no audio signal. Make sure that the audio source is playing and sending a signal to the subwoofer.
If none of these steps resolve the issue, there may be a problem with the amplifier or power supply in the subwoofer.
Not finding what you are looking for?