Philips Ovens - Popular Questions, Answers, Tips & Manuals

Consult owners manual.

Several things can shorten the life of bulbs. It could be a factory defect, the filament is receiving too much voltage, physical shock while the filament is heated, vacuum leaks in the bulb seal or base. Suggest try another brand preferably heavy duty.

I can fix this for you. Where are you residing please? Thanks David. "The Famous Forry'

If you have a multimeter I would FIRST turn off the power and disconnect the heating element and do a continuity check on it. Phillips elements are not all that durable, so that is probably the problem, but it could be the thermostat or switch also. Some Phillips also have thermofuses that seem to blow for no aparent reason.

sounds like the eliment has gone hard to get parts i am looking for user manual for this model

Try in THIS LINK

I hope helps.

Either the temperature sensor has a problem (shorted so the control thinks the oven is colder than the actual temp) or a relay feeding the bake or broil element is welded shut and causing one of the elements to stay on. If the elements are still heating when the "ON" indicator is NOT lit, then you have a welded relay. You need the control board repaired.

If the fan is working o/k, then it is more than likely that the oven element has failed.
This is to be found at the rear of the inner oven compartment behind a removeable cover.

May i get the model # to help you find the door.

If the fan is in the center at the rear of the oven where the element is, and the element is working o/k, then I would say that there is no doubt about it being the fan motor that is faulty.
The fan and element come on together as they are both fed together.
Please rate my solution.
Thankyou.

they make special appliance enamel touch up paint, which is good for a knick and a chip here and there. If its a bigger job than that, you may want to use a higher heat enamel. Ive used high heat engine enamel purchased at an auto parts store, which they formulate to work with the heat of car engines. It comes in a spray can, so it depends on the scope of the project/repair.

Re check the model number, that number doesn't pull anything up. If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

You can replace the light bulb(s) in your range/oven, though you may need to remove a glass covering or dome to reach it. Most interior oven lights use a universal 40 watt appliance bulb.

Fahrenheits unless you bought it overseas, the it would''nt work for there is a power voltage difference from here to there.

I have a vertical polin oven with single revolving rack. I need to sell it right away. Located in Plano Texas. Please contact me at 972 693 3137. - Jay ([email protected])

Well, I decided it probably is only a microwave, but one with a fan to blow the hot air around. SO I've given up on it and taken it back to the reverse garbage shop where I bought it.

Question edited for clarity. Two question amalgamated into one. Duplicate question deleted. Refresh page to see your question. Full 'make model (what it is)' in all questions please. High Temperature Silicone Sealant.

HIGH TEMP 100% RTV Silicone Sealant

Dap.ca https://dap.ca > caulks-sealants > specialty > high-temp Features & Benefits · High temperature formula · Service temp up to 550°F (intermitent) · Ideal for flue pipes & other high temp applications · Shrink & crack ...

DAP HIGH TEMP 100% RTV Silicone Sealant

Home Depot https://www.homedepot.ca > ... > Caulk & Sealants DAP HIGH TEMP SILICONE is a high-performance sealant designed especially for extreme high temperature applications. It provides a long-lasting, ... ..

Error code A03. Replacement: XFT135 XFT135-0D06 2230482. Sensor issues or bad wiring is the usual cause.

Question edited for clarity, wrong type of 'made' versus 'maid'. All questions need FULL 'make model (what it is)' please. It appears to be an obscure model GE wall oven? https://www.google.com/search?q=PSB9240SF6SS Turn it off at the breaker and leave it off overnight. In the morning press and hold any button for 2 minutes. This fully dissipates any memory in the control board. The reconnect the power. Not sure who 'Beniam' is? https://www.google.com/search?q=Beniam ..

Yes, they are usually the same element if the same shape.. Or just buy a new one? https://www.google.com/search?q=West+King+universal+Vista+view+oven+replacement+element ..