Pelican Logo

Pelican Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 98 Products
  • 108 Answers
  • 21K Views

no may ne u need config it manually

Pelican PL-2050... | Answered on Jun 25, 2010


You are having a controller board problem I would suggest getting it repaired or replaced or you can take it apart and make sure everything is in working order such as no burnt buttons or melted solder.

Pelican Wired... | Answered on May 09, 2010


hira895

In regards to your wireless connection issue with your XBOX 360 do you have the wireless adaper connected to the XBOX. Note most XBOX 360's do not have a built in wireless adapter, some of the Elites do but most do not.

Hope this helps

Issken

Pelican PL-2050... | Answered on Nov 07, 2009


r means right, (right trigger) l means left, (left trigger) I hope i helped. :)

Pelican Xbox... | Answered on Sep 30, 2009


could be that the adapter is a 3rd party adapter and that would be it doesn't pass the qualtiy that Sony requires before it puts its stamp of approval on the item which means your taking a chance on the item working.

See if you can find an item that is approved by sony and then try that.

Pelican Video... | Answered on Aug 28, 2009


Check to verify that your batteries are installed correctly.
- Check to verify that the power is on. Check to verify that the signal LED is blinking

If this does not solve the problem, do the following:

1. Make sure your Xbox is turned off.
2. Remove the battery lid and place 2 AA batteries into the Blade 2.4 Street Wireless Controller. Make sure the batteries are inserted as shown in the battery compartment.
3. Insert the receiver into your Xbox controller slot of your choice and power up the controller FIRST, then your Xbox.
4. Press the Connect button on the receiver once. Your signal LED light will begin to flash slowly.
5. Press the Back button on your controller. This will program the receiver to connect to the controller each time it is uses.
6. Turn on your Xbox and insert a game.

Pelican PL-2050... | Answered on Aug 06, 2009


see if you can find drivers for the interface...

Pelican Cobra TT... | Answered on Jul 24, 2009


are you using the game to reasign or the actual windows program

Pelican XBOX... | Answered on Jul 09, 2009


pull it if it is stuk in or push it if it stuk out

Pelican Xbox... | Answered on Jun 11, 2009


Run the network tests from within the 360 menus - looking especially at the result for network address translation (NAT). If this is either limited or fail, you will need to change your router for one which is compatible with xbox live. Try xbox.com to work out which routers are recommended.

As far as your router kicking him when you connected your pc, then you must have altered the access permissions of the router maybe by accident.

If all else fails, turn off the pc, router, modem and 360. Find the reset button on your router and press/hold this for at least five seconds. Turn on the modem, then the router. Let that settle for a minute, then connect and setup 360 and laptop.


Pelican PL-2050... | Answered on Apr 10, 2009


There is a little white buttom on your xbox , this is the sync buttom , on your remote there is a small round white buttom too ( sync buttom again ) press those 2 and it will find your new controller

Pelican XBOX... | Answered on Feb 25, 2009


Need more information for this... if you would like help.. but it really wouldn't matter if you have your remote taken apart and you just need to put them back in but R stands for Right and L stands for Left if you didn't know that

Pelican Xbox... | Answered on Nov 11, 2008

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Pelican Experts

abcollins98

Level 1 Expert

1 Answers

Benjamin Jeffrey
Benjamin Jeffrey

Level 1 Expert

34 Answers

Tom Chichester

Level 3 Expert

51297 Answers

Are you a Pelican Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...