Numark Recent Questions, Troubleshooting Help & Support

I would ask the company you bought it from, they will have a list if repaires or take it to a good HiFi repair shop.

Question edited for a lot more clarity. 'Lite' is a completely different meaning as defined by Budweiser, Miller and Coors breweries. Help in the link. It appears to be a known issue. https://www.google.com/search?q=Numark+Mixdeck.+Nothing+displayed+on+the+the+screen ..

Hello, did you get this repaired in the end? Same thing is happening to mine and I don't know what's causing it

You could contact Numark to check if your version is compatible with Windows 7. https://www.google.com/search?q=Numark+Party+Mix& The contact Serato and pitch the one against the other. You need both software version to work with Win 7. https://www.google.com/search?q=Serato ..

If your Numark 5000FX mixer is not registering your Technics turntable on any of the channels, there are a few things you can try:

1. Check your cables: Make sure that your RCA cables are plugged in correctly and securely. If you are using a phono preamp, make sure that it is powered on and connected properly.
2. Check your switch settings: Make sure that the switches on the back of the mixer are set correctly for the type of input you are using (line or phono).
3. Check your levels: Make sure that the input levels are turned up and that the fader for the channel you are using is not muted or turned all the way down.
4. Check your ground wire: If you are using a turntable, make sure that the ground wire is connected properly to the mixer.

If none of these steps work, there may be an issue with either the turntable or the mixer. Try testing the turntable on a different mixer or testing a different turntable on the Numark mixer to determine which component is causing the issue. If the mixer is the issue, it may need to be repaired or replaced.

Check the connections for a bad earth link.

Check the cables are pushed in correctly on the back of the devices. Try swapping the data cables around.

Question edited to throw in a few capital letters for Proper Names and abbreviations. It doesn't need to read the cleaning CD as the act of looking for the tracks is enough to brush the optics clean. If that didn't work, you need a audio tech.

Question moved to make/model category. It appears to be a known issues. See the videos https://www.google.com/search?q=Numark+TT500+turntable+will+not+spin ..

Question edited for clarity Nunark to Numark. Question moved from Television category. You could use the line outs if the sound bar has the same jacks, line in. https://www.numark.com/product/ndx400 ..

I find it hard to believe some of these answers. If the platter is wobbling, if you remove the platter, you'll find the spindle the platter rotates on. That will probably be loose. At the bottom of the spindle bearing, you will find a nut. Tighten that, and you should be in business. If you have further questions please visit my website at audioserviceclinic.com. You may contact me there.

not told model numbers of both impossible to be specific but this read he EQ manual yet?

Hi,
Make sure you install the software in the CD provided with the iDJ3. IF you already have, try to uninstall, restart and then reinstall. Sounds like the drivers for your device was not properly loaded to your PC which cause it not to recognize. If it still doesn't work after that, I suggest that you contact Numark tech support for further troubleshooting at this link: http://www.numark.com/content54
Good luck and vote this solution if it helped you. Cheers

it should just be plug and play but in your config make sure your controller is your soundcard. but if need the drivers www.numark.com or www.virtualdj.com

That will be located probably on the model number plate on the turntable itself. Or somewhere on the turntable itself. Since it's unique to the turntable nobody else will have it.

when things work they do not need cleaned

same problem here...

Your belt is probably worn and needs replacing. Lift felt on platter and and lift the platter section off the unit by putting your thumb and forefinger through the two large holes and pull upwards.There should not be any special routing for the belt and should go directly onto the spindle motor to your platter. Place the belt around the inside rim of the platter while it is still off the unit. Now replace the platter and move the platter around until you see the spindle motor through one of the holes. Use some tweezers to manouvre the belt onto the spindle motor. On some units you will have to lay the belt out inside the unit, replace the platter and manouvre the belt onto the platter. Hope this helps

I think you have been lucky! Many manufacturers do not want you to do your own servicing or updating, and guard their Technical stuff jealously. Letting anyone use it opens it up to copycat manufacturing.