NRS Recent Questions, Troubleshooting Help & Support

Question edited for clarity, Hoveround not Hooveround. Added '(what it is)'. All question need full 'make model (what it is)' please. Question moved from 'Rode Microphones'. Bad connection on your motor. Bad connection on one of your batteries. Or a motor, or the controller / board has failed. all can be tested. https://www.google.com/search?q=hoveround+goes+in+circles ..

Are you trying to find the top manual testing companies in Pune, India? Look nowhere else! Our list of the best manual testing companies is based on various criteria, including experience, skill, client happiness, and cost. We have the ideal manual testing business for you, regardless of whether you are a startup or a huge corporation. For a free consultation, get in touch with us today!

Replace the batteries and charge before use then charge nightly for 20 days Use the chair daily so you can get a good charge nightly to get the batteries operating at 100% After the 20 days If you don't use the chair daily always store fully charged and then charge once a week overnight. Should work fine once you get the new batteries in You will need to get 2 U1 batteries for your chair do not get Wally World or automotive batteries You must replace with sealed deep cycle batteries made for power chairs Hope this helps

Given that the serial number contains the year and week of manufacture, determining the age of a water heater is quick and simple. The manufacturer's label, which is attached to the body of the unit, contains this information. https://www.usawaterquality.org/whirlpool-water-heater-age/

Question edited for a lot more clarity. Question moved from Cars and Trucks. https://www.google.com/search?q=Ramset+J20+firing+pin Ramset J20 parts and repair video https://www.paslode.co.nz/schematic-au/zz-historical-retired-ramset-tool-schematics-no-parts-support/powder-actuated-no-support/409-j20-j20s-ramset-au/file

The pressure loss is due to either a plugged distributor/manifold or upper basket. The head must be removed for access to the manifold and upper basket. The manifold runs from the head to the bottom of the tank. This is where all the soft water is drawn from and is the most likely cause for pressure loss. Water must be shut off and tank depressurized before attempting to remove the head of softener to access these parts. Clean the slots in the manifold and upper basket. They are probably plugged with iron, resin and/or gravel and re-install.
RJ

There's a small O-ring hidden inside that seals the vent hole. It's in a recessed ring in the blue body, under the white plastic rotating part on top under the handle. Some report success by just tightening the main screw on the underside within the housing. I've found the O-ring too thin and stiff to make a good compression seal. To access it you remove the handle (via a screw with loose washer), and remove the two white underside parts by another screw, both flat-head type. There's at least three other O-rings on shafts to not lose or break. I've never bought a new ring, but instead inserted a couple layers of electrical tape to bridge the gap, and gave up the convenience of the venting, because I have valves I can close on both sides. Replacing the ring could work; it's about 5/16" o.d. x 3/16" i.d.

sorry to tell u this but with a new controller and joystick u will need a tech with a programmer to redo the joystick and det up controller,so contact a dealer for help

CHANGE HER BATTERIES

The full manual is not available online. It must be purchased directly from Hoveround for $20 plus shipping. Please call 800-964-6837, you will need the serial number from your power chair, located inside the manual brake release above the footrest.
Good luck!

The solenoid is what makes the starter gear pop out to engage the flywheel to turn the motor. If the solenoid is bad, the starter gear won't pop out. If the starter gear does pop out, then the solenoid is good. The starter motor should turn even if the solenoid is bad.

We have tried the reset button and also squeezed both of her palms. What else should we try? Any suggestions?

guessing could be if it comes with software to reload soft ware or go to suppliers site and type in your question

If you plug the charger into the wall, turn on the power switch and the light comes on, the charger should be working properly. Here is a way to test it-
Attach the charger that came with the power chair to the power chair controller firmly and turn the power chair on, while the charger is running. What should happen:the lights on the controller will scroll back and forth. If this does NOT happen and you can confirm the charger is turned on, the charger handle is fully seated inside the controller receptacle and the wall outlet has power, then the charger may have a problem and needs to be replaced.

If the charger is OK, then there may be a problem with the batteries. Here are some sypmtoms:
1-You connect the charger but the light on the charger never goes red, it just stays green.
2-You connect the charger but the light goes from red to green VERY fast.
3-The charger light goes from red to green but when you disconnect the charger and press the power button on the controller, you only have one flashing red light, or the batteries drain within just a few minutes of use.
4-The power chair has been stored or sitting idle for several months.
5- The power chair has been connected to the charger 24-7 for several months.
Any of the above examples indicates that the batteries are oxidized or damaged and will most likely need to be replaced. The MPV5 takes two, U1 12 volt 33 amp batteries which can be purchased at any battery warehouse store like Interstate Batteries or Batteries Plus.
Good luck!

on my jxd mp4 & mp3 player THERE IS WHITE SCREEN