How do I get the agitator rotate
The motor in the top of the machine should rotate the gear sticking out of the top of the cabinet when you turn the switch on. This gear should connect with a gear on the top of the shaft that sticks out of the kettle when the kettle is in the correct upright position and turning the stir rod.Make sure the kettle is installed correctly, and the switch is in the on position. If the motor is not turning with the switch on, it is broken and should be returned to store if possible. There are no repair parts for this brand popper, and they cannot be repaired.
9/5/2013 8:03:59 PM •
Nostalgia...
•
Answered
on Sep 05, 2013
•
352 views
Margarator
Parts for Nostalgia Electric are not available anywhere.
5/2/2013 3:05:39 PM •
Nostalgia...
•
Answered
on May 02, 2013
•
304 views
The third select button will not stop down
I have a model 464 and my problem was similar but mine was the second digit.I replaced the p c board in the selection control box and my problem was gone.I would check the selection control box.Hope this helps
1/17/2013 5:16:43 AM •
Nostalgia...
•
Answered
on Jan 17, 2013
•
572 views
The popcorn gets stuck in the kettle until it
I have a Popcorn machine from Nostalgia too that had this problem. I cleaned it out and everything but it still had the problem of the it getting stuck. After days of analizing, I found the solution. after a while the ceiling of the popcorn machine starts to fall in, lowering the handles of where the kettle goes. making the knob that turns being lower that the one that makes it turn, causing it to get stuck, all I did is add so leverage so the kettle is once again at the same level or higher. Making it turn with greater force and not getting stuck. In other words make sure the turning mechanism is leveled and not one lower than the other. preferably the kettle part being higher.
5/24/2015 6:22:20 PM •
Nostalgia...
•
Answered
on May 24, 2015
•
14,253 views
How to fix this problem?
See if the gear at the top of the kettle rod is "jumping" and not allowing tehe stirrer to rotate properly. In my machine, this was caused by a broken black guide at the atop the two gears. The guide is screwed into place. It allows the gear to slide in and out as you rotate the kettle, but it also has to prevent the rod from moving back and forth or the gears will slip
9/18/2012 4:11:35 AM •
Nostalgia...
•
Answered
on Sep 18, 2012
•
430 views
Will not heat up and pop
Your power cord I would follow into the machine and hunt for a broken wire or a blown fuse possibly. Most pop corn makers are just about like a coffee pot. They have a klixon to control the temp and a couple of bullet fuses in line to prevent over heating. All of which is loacted on the base of the kettle. I wish I could be there to help ya get that popcorn popper working. Feetball season is nearly upon us.
Contact the makers If you need further help, reach me via phone at
https://www.6ya.com/expert/dan_73bbd84fe1d95b61
8/5/2012 6:34:55 PM •
Nostalgia...
•
Answered
on Aug 05, 2012
•
429 views
I need the instructions for nostalgia ice cream
Hello, I have located the manual that you requested for your nostalgia ice cream maker ICMP400BLUE. You can retrieve the manual by either clicking on this link or copy and pasteing the link to your browser. If you have any issues in reading this manual or retrieving it from the link that I have provided please message me back and if also you have any questions at all either on this appliance or any other you can also message me with any of those as well. Please also remember when our chat has fully concluded to rate how this service has performed in helping you to locate your manual. By doing this it allows me to continue helping others in similar situations for others in the future. Click this link
http://www.nostalgiaelectrics.com/manuals/ICMP400BLUE.pdf Thank you again I await any further questions and Have a Happy New Year,Rick
12/31/2011 8:12:52 PM •
Nostalgia...
•
Answered
on Dec 31, 2011
•
159 views
Not finding what you are looking for?