Nostalgia Electrics Audio Players & Recorders - Answered Questions & Fixed Issues

I have a model 464 and my problem was similar but mine was the second digit.I replaced the p c board in the selection control box and my problem was gone.I would check the selection control box.Hope this helps

error code 30 =memory contents invalid you need to reprogramme

Gee, Google found it and a source. "Sylvania SRCD 820 needle".

Why waste time putting this on Fixya?

http://www.lpgear.com/Merchant2/merchant.mvc?Screen=CTGY&Store_Code=LG&Category_Code=SYLVANIASTY

I am not sure it is much help but as far as I know the eprom is in the computer. The computer is directly below the CD player.
So duff computer?

I HAVE THE MANUAL AND SERVICE PROGRAMME ON A DVD DISC EMAIL ME I WILL SEND IT [email protected]

The problem is probably in the keyboard. Clean all the contact switches you can get to with very fine sandpaper. The reason it is stuck is it is waiting for that third selection to complete the circuit.

error 73 means error during grip from magazine check for lift jamming,check function and adjust,i had one recently the same fault found it easy to replace the cd changer complete for 65.i do have the manual and service guide if you need one just email me

No, but like any machine, it does need lubrication once in a while. You should purchase a manual for it (eBay).
If the clutch has become stuck, it's time to call in a pro.
Are you sure it's in "PLAY" mode? Check to be sure the service switch is in "PLAY."
Does the motor turn?
If yes, try pressing the reject button on the back. Maybe it's stuck thinking it's playing a record in an empty slot (clamp arm will be against the turntable). There is also a manual trip lever just to the right of the tonearm. lift up on it if the motor is turning and see if that triggers it. Go ahead, it won't hurt you.
if the motor itself has frozen up from lack of oil, try putting some light machine oil (NOT 3-in-1 or anything paraffin based) in the oil cups on the side of the motor and letting it sit for a few hours. Then, turn the motor shaft by hand a little. This may free it up. if so, count your blessings and call someone in to give the whole mechanism a proper lubrication or something else will eventually seize up or wear out.
Good luck.

release the orange case from the back and slide forewards.Note,use athin knife blade to ease the case sides 2no. from holding points on head.BUT THERE MUST BE A BETTER WAY???.

Hi,

I do not know where to get the lamps however here is the information re the maker.

Helman Group WCD4090 CD Shelf System
www.helmangroup.com
www.hktdc.com

I hope this helps.

Regards
Alan Hood
ami-man
UK

Hello,

If you are in the USA you can order a manual from a list of dealers that can be found on www.roweinternational.com or from www.victoryglass.com

Regards
Alan Hood
ami-man
UK

You put sugar or "floss" in the center of the spinner. When it heats up (takes a while) a spider web like material forms in the bowl. You take a "paper cone" and twirl it around to collect this which is the cotton candy! Find a party store to get the cones and you can also get the "floss" which is sugar with a bit of coloring and sometimes glycerin.

Clean the spinner after use.

THIS IS A COMMON PROBLEM. THE ONLY SOLUTION IS TO REPLACE THAT DOME.
GLUING WILL NOT WORK. APOXY WILL NOT WORK. THERE IS A LOT OF PRESSURE
AT THAT PLACE.

REPLACE THAT DOME IS THE WAY TO GO. GET N FRIENDS TO HELP, OR YOU WILL BREAK THE NEW DOME.

[email protected]
MAME IS SEYMOUR LEVITT
COMPANY NAME IN-HOME JUKEBOX REPAIR
6362273300
746 HENRY AVE BALLWIN MO.

If you've checked the cables, swapped them out, and ensured that the power adapter is providing power to the Vocalizer 3, but you're still not getting any sound output, there are a few additional troubleshooting steps you can try: 1. **Check Volume Levels**: Ensure that the volume levels on the Vocalizer 3 and any connected devices (such as mixers, amplifiers, or speakers) are turned up and not muted. 2. **Test with Different Inputs/Outputs**: Try connecting the Vocalizer 3 to different inputs on your mixer, amplifier, or speakers, and test with different output devices if possible. This can help determine if the issue is specific to certain connections or devices. 3. **Inspect Settings**: Check the settings on the Vocalizer 3 to ensure that the correct input and output sources are selected. Make sure that any settings related to mono/stereo output are configured correctly. 4. **Test with Different Power Adapter**: If you have access to another power adapter with similar specifications, try using it to power the Vocalizer 3. This can help determine if the issue is related to the power adapter. 5. **Reset the Vocalizer 3**: Some electronic devices can benefit from a reset to their factory settings. Refer to the user manual for instructions on how to perform a reset on the Vocalizer 3, and try resetting it to see if it resolves the issue. 6. **Contact Technical Support**: If you've tried the above steps and are still experiencing issues with the Vocalizer 3, it's possible that there may be a hardware problem or malfunction. Contact the manufacturer's technical support for further assistance and troubleshooting guidance. They may be able to provide additional insights or recommend repairs if necessary. By following these troubleshooting steps, you should be able to diagnose and resolve the issue with the lack of sound output from your Vocalizer 3.

1. Power Off: Turn off the device.
2. Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
3. Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
4. Power Off Again: Turn off the device once more.
5. Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
6. Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.

If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.

this model SA rather than SC seems to be a Middle East model. The SC version doesn't have DAB. https://www.google.com/search?q=panasonic+sa-pm250+instruction+manual ..

All questions need clear 'make model (what it is)' first 3 words. https://www.google.com/search?q=fmdott085+V398 ..

Question edited for clarity, typo and CAPS. Question moved from Cars and Trucks category. Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries. How long is the warranty on AfterShokz? While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase. Jan 11, 2019

How To File A Warranty Claim For Your SHOKZ Headphones

https://www.google.com/search?q=Openfit+Shokz+battery+replacement ..

Are you using the charging cables that came with it? That is a type C. Are you securely attaching the charging cable? A loose connection would keep the battery from charging. If you had a low battery, you would see a red light. That you have no light at all suggests there is no charge left in the battery. I'm not sure the reset will work with no charge which is why you ought to check the cables first. But turn it off and then hold down the Multifunction button for 10 seconds to reset it. Then turn it back on and see what happens. If you can, test the charging cable on aother device. If you have another type C charging cable, try it, just to eliminate a bad cable. If these suggestions don't work, you may try the manufacturer's customer support.

The F2100 remote is not explicitly listed as compatible with the AerialBox T2100, I recommend using the remote that came with your AerialBox T2100 for optimal functionality. If you have any specific compatibility concerns, I suggest reaching out to Dish TV customer support for further assistance.